How to choose a floor jack: 3-ton low-profile hydraulic floor jack with dual-piston pump

How to Choose a Floor Jack: Capacity, Lift Range and Safety

Here's how to choose a floor jack in one paragraph: pick a rated capacity comfortably above the weight you'll lift at one corner, check that the lowest saddle height slides under your car and the highest height lifts it far enough to get a wheel off, look for a dual-piston pump if you want fewer handle strokes, and buy a matching pair of axle stands at the same time. A floor jack lifts the car. Axle stands hold it up while you work. You need both, every time.

We sell floor jacks, axle stands and the hand tools that go with them at Easy Life Auto Parts, including two 3-ton low-profile hydraulic floor jacks, a set of 3-tonne ratchet axle stands and a compact 12V electric jack kit for roadside use. This guide covers what the numbers on a jack actually mean, which type suits which car and garage, how to lift a car safely, and how to keep a jack working for years. Where we lean on an outside fact, we link to the source so you can check it yourself.

How to choose a floor jack: blue 3-ton low-profile hydraulic floor jack with dual-piston quick-lift pump

What This Guide Covers

How to Choose a Floor Jack: The Quick Checklist

  1. Capacity: 2 tons covers most small cars; 3 tons gives headroom for SUVs, vans and light pickups.
  2. Minimum height: measure the gap under your jacking point. Lowered and sporty cars need a low-profile jack starting around 3 to 3.5 inches.
  3. Maximum height: trucks and lifted 4x4s need a jack that reaches 18 inches or more.
  4. Pump: dual-piston pumps lift the saddle to the car in fewer strokes.
  5. Saddle: a rubber pad protects pinch welds and paint.
  6. Weight and size: heavy steel jacks are stable but stay in the garage; light ones go in the boot.
  7. Axle stands: buy a pair rated at least as high as the jack, and never work under a car supported only by the jack.

The rest of the guide takes each point in turn, starting with the type of jack.

Floor Jack vs Scissor Jack vs Bottle Jack vs Electric Jack

Before you get into capacities and heights, it helps to know what each kind of jack is for. Part of learning how to choose a floor jack is knowing when a floor jack is the wrong tool.

The Scissor Jack in Your Boot

Most cars come with a small scissor jack and a wheel brace. It folds flat, weighs very little and is designed for one job: lifting one corner far enough to swap a flat tyre at the roadside. It's slow, it has a tiny base, and it's tuned to your car's specific jacking points. It is fine for an emergency wheel change. It's not a garage tool.

The Bottle Jack

A bottle jack is a vertical hydraulic ram. It's compact and can lift a lot of weight for its size, which is why you'll see them with trucks and vans. The catch is height: the starting height is often too tall to fit under a normal car, and the small top pad makes it easy to miss the jacking point. Bottle jacks suit high vehicles and workshop presses more than everyday cars.

The Floor Jack (Trolley Jack)

A floor jack, also called a trolley jack, is a long, low hydraulic jack on wheels. You roll it under the car, place the saddle under the jacking point and pump the handle; a long lever arm raises the saddle in an arc. Floor jacks are stable, quick and easy to position, which is why they're the standard for home garages and tyre shops. If you rotate tyres, change brake pads, swap wheels for winter or do any work under the car, this is the jack you want.

The Electric Jack

If you came here wondering how to choose a floor jack or an electric one, here is the difference. Electric jacks plug into a 12V socket and lift at the press of a button. They're convenient at the roadside, especially for anyone who struggles with a manual jack, and many come in a kit with an impact wrench for wheel nuts. They tend to have lower capacities and lower maximum heights than a full-size floor jack. Our vehicle-mounted electric jack kit is a good example: 2 tons, 120 to 350 mm lift and about 5 kg.

Quick Comparison

Jack type Best for Strengths Weak points
Scissor Roadside tyre changes Light, folds flat Slow, small base, low capacity
Bottle Trucks, vans, high vehicles Compact, high capacity Tall starting height, small pad
Floor (trolley) Home garage work on most cars Stable, fast, easy to position Heavy, needs a hard, flat floor
Electric 12V Roadside convenience Push-button, low effort Lower capacity and reach

Plenty of drivers end up with two: a floor jack for the garage and a scissor or electric jack in the boot. Pair either with a portable tyre inflator and you're covered for most tyre problems at home and on the road.

12V vehicle-mounted electric jack kit with carry case for roadside tyre changes

Capacity: How Many Tons Do You Need?

Capacity is the first number on any jack, and it's the one people most often get wrong, usually by overthinking it. Here's how to choose a floor jack capacity without guessing.

You Lift a Corner or an End, Not the Whole Car

A floor jack raises one corner, or one end if you lift from a central point such as a front crossmember or rear differential. That means it carries only part of the car's weight. A 1,500 kg family hatchback might put 400 to 600 kg on one front corner, because the engine sits at the front. Lifting the whole front end through a central point puts roughly half to 60% of the weight on the jack.

Find Your Car's Weight

The first practical step in how to choose a floor jack is finding a number. Look for the kerb weight in the owner's handbook, or the gross vehicle weight on the plate inside the driver's door frame or under the bonnet. Gross weight is the maximum loaded weight, so it gives you a safe upper figure to plan around.

A Simple Rule of Thumb

Pick a jack rated for at least the full kerb weight of the car if you can, or at the very least comfortably above the weight of the end you'll lift. Headroom matters because hydraulic seals and the lifting arm work less hard when they're well inside their limit, and because cars get heavier when you load them. The UK Health and Safety Executive's guidance on working under vehicles tells workshops never to exceed the safe working load of any lifting equipment. The same rule applies at home.

Vehicle Typical kerb weight Sensible jack rating
City car or small hatchback Around 900 to 1,300 kg 2 tons
Family saloon, estate or crossover Around 1,300 to 1,800 kg 2 to 3 tons
Large SUV, people carrier, light pickup Around 1,800 to 2,700 kg 3 tons
Heavy pickup or large van 2,700 kg and up 3 tons or more, plus high lift range

The weights above are broad ranges for illustration, not figures for a particular model. Always check your own vehicle.

Why 3 Tons Is the Popular Choice

A 3-ton jack costs only a little more than a 2-ton one, handles nearly every car, SUV and light truck in a typical driveway, and means you won't need a new jack when you change cars. That's why both full-size floor jacks we stock are rated at 3 tons (about 6,600 lb). Our 3-tonne axle stands are rated to match.

Tons, Tonnes and Pounds

Jack ratings switch between units, which can be confusing. A metric tonne is 1,000 kg. A US "ton" is 2,000 lb, about 907 kg. Many jacks sold worldwide are labelled "3 ton" and "6,600 lb" side by side, which works out at roughly 3,000 kg, so treat that figure as about three metric tonnes. If you're comparing two jacks, convert both to kilograms.

Hydraulic low-profile steel racing floor jack rated 3 ton with dual pumps

Lift Range and Low-Profile Clearance

Every floor jack lists two heights: the minimum (how low the saddle sits when fully down) and the maximum (how high it goes). These two numbers decide whether a jack will actually work on your car. If you only remember one thing about how to choose a floor jack, make it this: measure first.

Minimum Height: Will It Fit Under?

Measure from the ground to your car's jacking point, then subtract a bit for a flat tyre, which drops the car further. Sports cars, lowered cars and some modern saloons with deep front bumpers may have only 4 or 5 inches of room under the jacking point. A standard jack starting at 5.5 inches won't slide in. A low-profile jack, starting around 3 to 3.5 inches, will.

Our two floor jacks are both low-profile designs. The 3-ton low-profile floor jack starts at about 3.1 inches, and the steel racing floor jack starts at about 3.3 inches.

Approach Length: Will It Reach?

Height isn't the only clearance issue. On many cars the jacking point sits a long way under the body, behind the bumper or side skirt. A long-chassis floor jack reaches further in before the front of the jack body hits the bumper. If you work on low cars with long front overhangs, a long, low jack is worth the extra weight. Some people also drive the front wheels up onto low ramps or wooden boards first, to gain an inch or two.

Maximum Height: Will It Lift Far Enough?

The car needs to go high enough for the tyre to clear the ground with room to spare, and high enough to fit an axle stand under it. For a normal car, around 14 to 15 inches is usually plenty. For SUVs, pickups and lifted 4x4s, where the suspension droops a long way before the wheel leaves the ground, look for 18 inches or more. Both of our floor jacks reach about 18.5 to 18.7 inches, which suits most cars and many SUVs and light trucks. Very tall lifted trucks may still need more.

Match the Jack to the Stands

When you think about how to choose a floor jack, think about the stands as well. Your axle stands have a height range too. The jack must lift the car higher than the height you'll set the stands at, so you can slide them in and lower the car onto them. Our 3-tonne axle stands adjust from about 280 to 420 mm (around 11 to 16.5 inches), which sits nicely within the range of both of our floor jacks.

Low-profile floor jack showing about 3.1 inch minimum saddle height for lowered cars

Pumps, Saddles, Handles and Wheels

Once capacity and height are sorted, the details decide whether a jack is pleasant to use or a chore. This is the part of how to choose a floor jack that you'll notice every time you use it.

Single-Piston vs Dual-Piston Pumps

Every stroke of the handle pushes hydraulic oil into the lifting cylinder. A single-piston pump moves one measure of oil per stroke. A dual-piston pump has two pistons working together, so it moves more oil per stroke while the saddle is unloaded and rises much faster to meet the car. Once the saddle takes the weight, most dual-piston jacks behave like a normal jack and lift steadily.

In practice that means far fewer strokes to get the saddle up to the jacking point, which you'll appreciate when you're working round all four corners. Both floor jacks we sell have dual-piston pumps. The supplier listing for the racing floor jack describes it as lifting up to five times faster than a single-piston design; we haven't tested that figure, so take it as the maker's claim.

The Release Valve

To lower the car, you twist the handle to open a release valve. A good valve opens gradually, so the car comes down slowly and under control. A poor one drops suddenly. When you first get a jack, practise lowering it with no load so you know how far to turn. Always lower slowly, and keep your feet and hands clear.

The Saddle

The saddle is the round cup that touches the car. Bare steel saddles can dent pinch welds and scrape paint and underbody coating. A rubber pad spreads the load and grips better. The racing floor jack has a 360° rotating, removable rubber saddle pad. For unibody cars that lift on a pinch weld, a slotted rubber pad that straddles the seam helps a lot. The listing for our 3-ton low-profile floor jack recommends checking your owner's manual for the jacking points and using a pad on unibody vehicles, which is good advice for any jack.

The Handle

Handles get little attention in most guides on how to choose a floor jack, but you hold one every time. A longer handle gives more leverage, so each stroke takes less effort, and keeps you further from the car. Two-piece handles split for storage. Look for a foam bumper on the handle so it doesn't dent the bodywork if it swings into the car. The racing jack uses a 44.9-inch two-piece handle; the low-profile jack has a foam handle bumper.

Wheels and Castors

Floor jacks roll on two fixed front wheels and two swivelling rear castors. As the arm rises in an arc, the jack has to roll forward slightly, so the wheels need to turn freely. Steel wheels are tough and suit smooth concrete. On rough concrete, small stones can jam them, so sweep the floor first. Never use a floor jack on gravel, grass, soft tarmac on a hot day, or a slope.

Steel vs Aluminium

Material is a weight question more than a strength question when you weigh up how to choose a floor jack. Steel jacks are heavy, strong and generally cheaper. Their weight makes them stable, but they're a workout to carry. Aluminium jacks are much lighter for the same capacity, which makes them popular at track days, but they usually cost more. Some are hybrids with aluminium arms on a steel frame. Both of our floor jacks are steel: about 64 lb (29 kg) for the low-profile jack and about 67 lb (30 kg) for the racing jack. That's a garage tool rather than something you'll keep in the boot.

Spec Sheet Questions to Ask

  • What's the rated capacity, and in which unit?
  • What are the minimum and maximum saddle heights?
  • Single or dual-piston pump?
  • Does the saddle have a rubber pad?
  • How long is the handle, and does it split?
  • How heavy is the jack, and will you be lifting it into a car?
  • Does it state the safety standard it was made to?

Racing floor jack rubber saddle pad and dual-piston pump close-up

Why You Always Need Axle Stands

This section matters more than any spec in the guide. A floor jack is a lifting device. It is not designed to hold a car up while you're underneath it. Hydraulic seals can leak, release valves can be knocked, and a jack can roll or tip if the car shifts. Knowing how to choose a floor jack is only half the job; the other half is buying stands to go with it.

What the Safety Agencies Say

Safety regulators on different continents say the same thing in almost the same words. The UK HSE's guidance on working under vehicles says raised vehicles should be "always properly supported - do not rely on jacks alone". Australia's consumer safety regulator, in its vehicle support stands guide, puts it even more bluntly: "Never get under your car using only a jack." The same guide says DIY vehicle repair is associated with an average of five deaths and 160 injuries a year in Australia alone.

Stands Come in Pairs

Australia's guide also advises using stands on a hard, level surface and always in pairs. One stand under one side leaves the car balanced on a point. Two stands, one each side under the same axle or the same pair of support points, keep it level and stable.

How to Choose Axle Stands

The checks are similar to how to choose a floor jack, with a few of their own.

  • Capacity: stands are usually rated per pair or per stand. Check which, and buy a set rated at least as high as your jack.
  • Height range: make sure the lowest setting fits under the car once lifted, and the highest gives you enough working room.
  • Locking: ratchet stands adjust quickly; pin stands lock with a solid pin through the post. HSE notes that pin-type stands must use the proper pins, not screwdrivers or nails.
  • Base: a wide base spreads the load and resists tipping.
  • Saddle: a curved or V-shaped saddle cradles an axle or frame rail.

Our 3-tonne axle stands come as a pair, with ratchet height adjustment, cast iron posts, steel bases and a curved saddle, in red and black.

Check for Recalls

Jacks and stands are mass-produced, and occasionally a design fault slips through. In 2020, the US National Highway Traffic Safety Administration published a recall notice for a well-known brand of 3-ton and 6-ton jack stands because the ratchet pawl could disengage under load and let the stand drop. The lesson isn't to fear stands. It's to register your products where you can, check recall lists in your country now and then, and inspect stands before every use. HSE also recommends a competent person inspects stands in workshops every 12 months.

Backup Measures

Many mechanics slide the removed wheel flat under the sill beside the stand as a last line of defence. If the car ever dropped, it would land on the tyre rather than on you. It's a free habit worth adopting.

Pair of 3-tonne ratchet axle stands with cast iron posts and steel bases

How to Lift a Car Safely, Step by Step

Buying the right equipment is step one. Using it properly is what keeps you safe. Here's the routine we'd follow with any jack, drawn from the HSE and Australian guidance linked above and the owner's manual for your car.

  1. Pick your spot. Hard, level ground: a concrete garage floor or a flat driveway. No gravel, grass, slopes or soft tarmac.
  2. Secure the car. Handbrake on, in gear (manual) or Park (automatic), engine off, key out.
  3. Chock the wheels. Chock the wheels on the end that stays on the ground, front and back of the tyre. HSE lists chocking wheels as part of safe practice.
  4. Loosen wheel nuts first. If you're removing a wheel, crack the nuts a quarter turn while the tyre is still on the ground, using a breaker bar or the wrench from a socket and ratchet set.
  5. Find the jacking point. Check the owner's manual. It shows the reinforced lifting points for the jack and, separately, the points for stands.
  6. Position the jack. Roll it under, centre the saddle directly under the jacking point, and pump until it just touches.
  7. Lift steadily. Pump smoothly and watch the car. If anything slips, tilts or creaks, lower it and reset.
  8. Place the stands. Set both stands to the same height and place them under the stand points. Lock them.
  9. Lower onto the stands. Open the release valve slowly until the car's weight sits on the stands. Leave the jack in place, just touching, as a backup if there's room.
  10. Test before you go under. Give the car a firm push. It should not move.
  11. To finish, raise the car off the stands with the jack, remove the stands, lower slowly, and tighten wheel nuts to the torque in your handbook.

None of this takes long once it's routine, and it makes every job under the car safer, whether that's a brake pad swap, a tyre rotation or a check for bad wheel bearing symptoms.

Ratchet axle stand height adjustment with curved saddle for supporting a car

Common Mistakes When Using a Floor Jack

Knowing how to choose a floor jack won't help if it's used badly. Most jacking accidents come from a handful of habits. Avoid these and you avoid most of the risk.

  • Working under a car on a jack alone. We've said it already, and regulators say it louder.
  • Jacking on a slope or soft ground. The jack needs to roll slightly as it lifts; on a slope or soft ground it can tip or sink.
  • Lifting on the wrong point. Jacking under the floor pan, sump or a suspension arm not meant for it can dent the car or slip.
  • Forgetting the chocks. A car that rolls even slightly can pull off the jack.
  • Overloading. Exceeding the rated capacity strains seals and the arm.
  • Dropping the car. Opening the release valve too fast slams the car down, which can damage suspension parts and the jack.
  • Using improvised supports. Bricks, blocks of wood and piles of tyres can crack or shift. Use rated stands.
  • Skipping inspection. Leaking oil, a bent arm or a cracked saddle means the jack should be repaired or retired.

Steel floor jack lifting arm and wheels on a level garage floor

Which Jobs Need a Floor Jack?

A good floor jack and pair of stands open up most of the maintenance you can do at home. Thinking about the jobs you'll do is a useful way to settle how to choose a floor jack and what else to buy with it.

Tyre Rotations and Seasonal Wheel Swaps

If you swap between summer and winter wheels, or rotate tyres every few thousand miles, a fast dual-piston jack saves real time. Lift, stand, swap, lower, and move to the next corner. Pair it with a digital tyre inflator to set pressures once the wheels are back on.

Brakes

Brake work is a common reason people look up how to choose a floor jack in the first place. Changing pads and discs means taking the wheel off and working at hub height. Our guides to ceramic vs semi-metallic brake pads and drilled and slotted rotors cover the parts side; the brake parts collection has the hardware.

Suspension and Steering Checks

With the wheel off the ground you can rock it to feel for play in bearings, ball joints and arms. See our posts on bad control arm symptoms, shock absorbers vs struts and bad CV axle symptoms for what to look for.

Oil Changes

Some cars need lifting to reach the drain plug and filter. An adjustable oil filter wrench set grips filters that won't come off by hand. Always use stands, because you'll be lying directly under the engine.

Diagnosis

Lifting the car lets you trace leaks, inspect the exhaust and look for damaged parts. If a warning light started it all, an OBD2 scanner and our check engine light codes guide help you narrow it down first.

Cr-V socket and ratchet wrench set in a case for removing wheel nuts

Looking After Your Jack

A floor jack is a simple machine, and a little care keeps it lifting smoothly for years. Durability is an underrated part of how to choose a floor jack: a well-made jack that's looked after will outlast several cars.

Store It Lowered

Always store the jack with the saddle fully down and the release valve closed. That keeps the ram inside the cylinder, where it's protected from dust and rust, and takes pressure off the seals.

Keep It Clean and Dry

Wipe off road grime, brake dust and water after use. Moisture and grit are the main enemies of the ram and seals. If you live somewhere damp or near the coast, a light coat of oil on bare steel parts helps prevent rust.

Lubricate the Moving Parts

Every few months, put a few drops of light oil on the wheel axles, castor swivels, the arm pivot points and the pump linkage. Check the manufacturer's manual for specific grease points.

Check the Hydraulic Oil

Serviceability is worth a thought when you decide how to choose a floor jack: look for one with an accessible fill plug. If the jack won't lift to full height, lifts slowly or sinks under load, it may be low on oil or have air in the system. Many jacks have a fill plug and a bleeding procedure in the manual. Use hydraulic jack oil, not engine oil or brake fluid, which can damage the seals.

Inspect Before Every Use

  • Any oil leaking from the cylinder or around the pump?
  • Does the jack hold height under load without creeping down?
  • Is the arm straight, with no cracks near the welds?
  • Do the wheels and castors turn freely?
  • Is the saddle and its pad in good condition?
  • For stands: is the ratchet or pin locking firmly, and are the bases flat and uncracked?

If the answer to any of these is no, don't use it until it's repaired or replaced.

Low-profile hydraulic floor jack stored lowered with handle removed

Matching a Jack to Your Car and Garage

Here are a few common situations, and what we'd suggest for each. Use them as a shortcut for how to choose a floor jack that fits the way you actually work.

Small Car, Occasional Wheel Swaps

A 2-ton jack would do, but a 3-ton low-profile jack costs little more and won't limit you later. Add a pair of stands and a socket set, and you're set for tyre swaps and brake jobs.

Lowered or Sporty Car

Low starting height is the priority. Look for 3.5 inches or less, a long reach, and a rubber saddle to protect the sills. Our 3-ton low-profile jack, at about 3.1 inches, suits this well.

SUV, Pickup or 4x4

For bigger vehicles, how to choose a floor jack is mostly about reach. Look for 3 tons or more and a high maximum lift, at least 18 inches. Check that your stands go high enough too. Both of our floor jacks reach about 18.5 inches, which covers most standard-height SUVs and pickups. For lifted trucks, measure carefully, and see our guide to leveling kits vs lift kits for how ride height affects all of this.

Several Cars or Frequent Use

If you do lots of jobs, a dual-piston pump and a long handle make a real difference over a weekend. The racing floor jack with its rotating rubber saddle and two-piece handle is built for that.

Roadside Only

If you never work in a garage and just want an easier wheel change than the factory scissor jack, an electric 12V jack kit plus a portable jump starter is a compact roadside setup. Our winter car emergency kit guide covers the rest.

Racing floor jack with two-piece handle for SUVs and light trucks

The Jacks and Stands We Sell

Now you know how to choose a floor jack, here's our current lifting range, with the key specs from each listing. Every product links to its page, where you can see photos and full details. Specs come from the supplier listings; check each page before you buy.

Product Capacity Lift range Weight Best for
3-Ton Low-Profile Floor Jack 3 ton (6,600 lb) About 3.1 to 18.7 in About 64 lb Lowered cars, all-round garage use
Steel Racing Floor Jack 3 ton About 3.3 to 18.5 in About 67 lb Frequent use, SUVs and cars
3-Tonne Axle Stands (pair) 3 tonne each About 280 to 420 mm Pair Supporting the car while you work
12V Electric Jack Kit 2 ton 120 to 350 mm About 5 kg Roadside wheel changes

3-Ton Low-Profile Hydraulic Floor Jack, Dual-Piston Quick-Lift

3-ton low-profile hydraulic floor jack in blue steel

A low-slung steel jack that slides under lowered cars and still lifts high enough for many SUVs. The dual-piston pump brings the saddle up quickly, and a foam bumper protects bodywork from the handle.

  • Capacity: 3 tons (6,600 lb)
  • Lift range: about 3.1 to 18.7 inches
  • Pump: dual-piston quick-lift
  • Material: steel, blue finish
  • Weight: about 63.9 lb
  • Extras: foam handle bumper

Shop the 3-ton low-profile floor jack

Hydraulic Low-Profile Steel Racing Floor Jack, 3 Ton

Hydraulic low-profile steel racing floor jack with rubber saddle

A long, low racing-style jack with dual pumps, a rotating rubber saddle pad and a two-piece handle that splits for storage.

  • Capacity: 3 tons
  • Lift range: about 3.3 to 18.5 inches
  • Pump: dual pumps (listed as up to 5x faster than single-piston)
  • Saddle: 360° rotating, removable rubber pad
  • Handle: 44.9 inches, two-piece
  • Weight: about 66.8 lb

Shop the racing floor jack

3-Tonne Axle Stands, Set of 2

3-tonne axle stands set of two in red and black

The essential partner to any floor jack. A ratchet post adjusts quickly, and the curved saddle cradles an axle or frame rail.

  • Capacity: 3 tonne per stand
  • Height: about 280 to 420 mm, ratchet adjustment
  • Material: cast iron posts, steel bases
  • Saddle: curved
  • Colour: red and black
  • Pack: 2 stands

Shop the 3-tonne axle stands

Vehicle-Mounted Electric Jack Maintenance Kit

Vehicle-mounted 12V electric hydraulic jack kit

A compact electric hydraulic jack that runs from the car's 12V supply, for push-button roadside tyre changes. Use it on firm, level ground and never get under the car on it.

  • Type: electric hydraulic
  • Capacity: 2 tons
  • Lift range: 120 to 350 mm
  • Motor: 100 W
  • Weight: about 5 kg

Shop the electric jack kit

Tools That Go With Your Jack

A full answer to how to choose a floor jack includes the hand tools that finish the job.

Browse the full automotive tools collection and car accessories. Can't find what you need? Use our request a part form, or contact us with your vehicle details. Delivery and returns details are on our shipping and returns pages.

Adjustable oil filter wrench set with grid wrench and belt wrench

Buying Checklist

Before you check out, run through this list. It sums up how to choose a floor jack in a form you can tick off.

  1. I know my car's weight and the jack's capacity is comfortably above it.
  2. I've measured the gap under my jacking point and the jack's minimum height fits.
  3. The maximum height lifts my car high enough for the wheel and stands.
  4. I'm buying a pair of axle stands rated to match.
  5. I have a hard, level surface to work on.
  6. I have wheel chocks, a wrench for the wheel nuts and my car's handbook.
  7. I've checked the jack's weight and know where I'll store it.

Frequently Asked Questions

How do I choose a floor jack for my car?

Start with capacity: pick a jack rated comfortably above your car's weight, with 3 tons a safe choice for most cars, SUVs and light trucks. Then check the minimum height fits under your jacking point and the maximum height lifts the car far enough. A dual-piston pump and rubber saddle are worthwhile extras. Buy matching axle stands at the same time.

Is a 2-ton floor jack enough?

For most small and medium cars, yes, because the jack lifts only one corner or one end. For SUVs, vans and pickups, or if you want room to grow, 3 tons is the safer choice.

What does low-profile mean?

A low-profile floor jack has a low minimum saddle height, usually around 3 to 3.5 inches, so it fits under lowered or sporty cars that standard jacks can't reach. Our two floor jacks start at about 3.1 and 3.3 inches.

Can I work under a car on just a floor jack?

No. Safety regulators including the UK HSE and Australia's product safety regulator say never to rely on a jack alone. Always lower the car onto a pair of rated axle stands on hard, level ground before going underneath.

Where do I put the floor jack under my car?

Use the jacking points shown in your owner's manual. These are reinforced areas, often on the pinch weld along the sill or on a central crossmember or differential. A rubber saddle pad protects pinch welds.

What's the difference between a floor jack and a trolley jack?

They're the same thing. "Trolley jack" is more common in the UK, Ireland, Australia and New Zealand; "floor jack" is more common in North America.

Why does my floor jack sink slowly?

Usually a slightly open release valve, low hydraulic oil, air in the system or worn seals. Check the valve is fully closed, then follow the manual for topping up and bleeding. If it still sinks, stop using it until it's repaired.

How high should a floor jack lift?

For most cars, 14 to 15 inches is enough. For SUVs, pickups and 4x4s with long suspension travel, look for 18 inches or more.

Are aluminium floor jacks better than steel?

Not better, just lighter. The right pick depends on how you use it, which is the core of how to choose a floor jack. Aluminium jacks are easier to carry and popular at track days but usually cost more. Steel jacks are heavier, very sturdy and good value for a home garage.

Do you sell axle stands as well as floor jacks?

Yes. We sell a pair of 3-tonne ratchet axle stands alongside our 3-ton floor jacks, plus tools like socket sets and oil filter wrenches.

Final Thoughts

Knowing how to choose a floor jack comes down to a few measurements and one rule. Measure your car's weight and its ground clearance, buy a jack whose capacity and lift range comfortably cover both, pick a dual-piston pump and rubber saddle if you can, and never go under the car without axle stands. Get those right and you'll save time and money on tyre swaps, brakes and checks for years.

Ready to kit out your garage? Shop our 3-ton low-profile floor jack, the racing floor jack and 3-tonne axle stands, or browse all automotive tools. Questions? Our FAQ may already have the answer.

Sources and References

Back to blog