Bad Belt Tensioner Symptoms: 9 Warning Signs and How to Check Yours
Share
Quick answer: The most common bad belt tensioner symptoms are a squealing or chirping belt, a grinding or rattling noise from the front of the engine, a tensioner arm that bounces or chatters while the engine runs, a belt that wobbles, tracks off-centre or jumps off its pulleys, and accessories that stop working properly: a battery light, overheating or heavy steering. Gates, the belt and tensioner maker, says abnormal chattering or bouncing of the tensioner arm under normal operation means the tensioner has already failed, and that belt squeal points to insufficient tension (Gates). Dayco adds noise or resistance when you turn the pulley, sticking or notchy arm movement, and metal-to-metal contact or broken stops (Dayco).
A bad tensioner is usually a quick, inexpensive repair if you catch it early. Leave it, and the belt can slip or come off, and then your alternator, water pump and power steering can all stop at once. This guide explains each symptom, how to check a tensioner at home in a few minutes, how to tell a tensioner fault from a worn belt or a noisy accessory, and when to replace it. We stock belt tensioners and engine parts for Honda, Acura and Dodge models, plus the parts the belt drives, and we ship auto parts worldwide.
What a Belt Tensioner Does
Most modern engines use one long ribbed belt, the serpentine or drive belt, to turn the alternator, water pump (on many engines), power steering pump and air conditioning compressor. For that belt to grip the pulleys, it has to be tight, but not too tight. That's the tensioner's job.
An automatic tensioner is a spring-loaded arm with a pulley on the end. Underhood Service, a trade magazine for mechanics, explains that the spring applies just the right amount of force against the belt to keep it tight, and that the tensioner automatically compensates for wear and keeps the belt under constant tension (Underhood Service). It also absorbs shock loads, such as when the A/C compressor clutch cycles on and off.
The Parts That Wear
- The spring. Underhood Service notes that springs lose tension over time from exposure to heat, and a weak spring can't keep the belt tight, so it slips (Underhood Service).
- The damper. Many tensioners have a damper that stops the arm bouncing. Gates explains that as the damper wears, the arm can bounce away from the belt (Gates).
- The pivot bushing. The arm swings on a bushing. When it wears, the pulley tilts out of line with the belt.
- The pulley bearing. The pulley spins on a sealed bearing that can dry out, get noisy and eventually seize or wobble.
Any one of these can cause bad belt tensioner symptoms, and they often wear together.
9 Bad Belt Tensioner Symptoms
Here are the warning signs, starting with the ones most drivers notice first.
1. Squealing or Chirping Belt
The classic sign. A squeal on start-up, when you turn the steering, when the A/C kicks in or in wet weather means the belt is slipping on a pulley. Gates says plainly that belt squealing indicates insufficient tension on the belt (Gates). The cause might be a weak tensioner spring, or a belt that's worn and glazed. A quick chirp can also come from pulley misalignment.
2. Grinding, Rattling or Rumbling From the Front of the Engine
A worn tensioner pulley bearing makes a grinding, growling or rumbling noise that rises and falls with engine speed. Dayco points to noise or resistance when turning the pulley as a sign of potential bearing failure (Dayco). A rattle that comes and goes, especially at idle, can be the arm hitting its stop.
3. Tensioner Arm Bouncing or Chattering
Open the bonnet with the engine running and watch the tensioner arm (keep hands, hair and clothing well clear). A little movement is normal as the engine fires. A lot of movement isn't. Gates says any abnormal chattering or bouncing of the arm under normal operation means the tensioner has already failed (Gates). Underhood Service describes the same thing as excessive movement or rocking of the tensioner pulley, or "belt flutter" (Underhood Service).
4. Wobbling Tensioner Pulley
If the pulley visibly wobbles as it spins, the bearing is worn out. Underhood Service puts it bluntly: wobble means the bearings are shot (Underhood Service).
5. Belt Running Off-Centre or Coming Off
A belt that creeps towards one edge of a pulley, frays on one side, or jumps off completely is a big warning sign. Dayco says off-centre tracking, or a belt flipping off the tensioner, is a clear sign of bushing wear (Dayco tech tip). Gates explains that a failed pivot bushing lets the pulley fall out of alignment with the belt (Gates).
6. Battery Light or Weak Charging
When the belt slips, the alternator doesn't spin as it should. Underhood Service notes that when the alternator stops turning, there's no charging output and the battery starts to run down (Underhood Service). Dim lights, a battery warning light or a flat battery can all start at the belt. Our guide to bad alternator symptoms helps you rule the alternator in or out.
7. Engine Running Hot
On engines where the serpentine belt drives the water pump, a slipping or broken belt stops coolant flowing. Underhood Service warns that when the water pump stops turning, coolant flow stops and the engine begins to overheat (Underhood Service). Watch the temperature gauge. Our guide to car overheating causes covers other possibilities.
8. Heavy or Jerky Steering
On cars with a belt-driven hydraulic power steering pump, belt slip makes the steering heavy, especially at parking speeds. If the belt comes off, Underhood Service notes the steering suddenly gets very stiff and hard to control (Underhood Service). Many newer cars use electric power steering, which isn't affected.
9. Worn or Damaged Accessories
A tensioner that bounces or holds the wrong tension also hurts the parts it drives. Gates links diminished output and premature failure of the alternator, water pump or A/C compressor to tensioner problems (Gates technical bulletin). Underhood Service adds that too much tension can overload the belt and the shaft bearings on those accessories (Underhood Service). If you keep replacing the same accessory, look at the tensioner.
How to Check a Belt Tensioner at Home
You can check most tensioners in ten minutes with a socket or breaker bar and a torch. If you've noticed bad belt tensioner symptoms, these checks will usually tell you whether the tensioner is the problem.
Safety First
- Do the hands-on checks with the engine off, the key out and the engine cool.
- When you watch the belt with the engine running, keep hands, hair, ties and loose clothing well away from the belt and fan.
- Tensioner springs are strong. Hold the tool firmly and release tension slowly.
Step 1: Watch It Running
Start the engine and watch the tensioner arm and belt from a safe distance. Look for the arm bouncing or chattering, the belt fluttering, and the pulley wobbling. Have someone switch the A/C on and off and turn the steering while you watch. A healthy arm moves a little and settles. A failed one jumps around. Gates treats abnormal bouncing under normal operation as a failed tensioner (Gates).
Step 2: Check the Wear Indicator
Switch off. Many tensioners have marks cast into the housing that show where the arm should sit. Underhood Service explains that many units have marks showing the normal range in which the arm can pivot, and if the arm is outside those marks, there's a problem (Underhood Service). An arm sitting at the slack end often means a stretched belt or a weak spring.
Step 3: Look at the Belt
Check the belt for cracks across the ribs, missing chunks, glazing (a shiny, hard surface), fraying on the edges or uneven wear. Underhood Service gives the typical service life of a serpentine belt as about 60,000 miles or five years (Underhood Service). Edge wear on one side usually points to misalignment, often from a worn tensioner bushing.
Step 4: Spin the Pulley
Release the belt tension with your tool and slip the belt off the tensioner pulley. Spin the pulley by hand. It should turn smoothly and quietly. Feel for roughness, grinding or play. Dayco gives a useful rule: if the pulley freewheels for more than two rotations when spun, the grease has gone and the pulley needs replacing (Dayco tech tip). Check the other pulleys while the belt is off; Gates recommends rotating pulleys to check bearing condition (Gates).
Step 5: Move the Arm Through Its Range
With the belt off, move the arm from one stop to the other with your tool. Dayco says it should move smoothly from stop to stop without any movement between the tensioner body and the arm (Dayco). Gates adds that any sticking or roughness means the bearing surfaces are worn and the tensioner needs replacing, and that side-to-side motion means the bushing has failed (Gates).
Step 6: Check the Stops and Body
Look for shiny spots where metal has rubbed metal, and for cracked or broken stops on the arm or housing. Dayco lists metal-to-metal contact and broken or cracked stops as signs the tensioner needs replacing (Dayco). Also check for rust streaks or a leaking damper.
A note on spring strength: there's no simple home measurement for it. Underhood Service points out there are no specifications for measuring the resistance of the tensioner spring (Underhood Service). In practice, a belt that squeals even when it's new, an arm sitting at the slack end, or a tensioner that feels weak compared with a new one are the clues.
Tensioner, Belt, Idler or Accessory? How to Tell
Noise from the front of the engine could come from several places. Bad belt tensioner symptoms overlap with a worn belt, a bad idler pulley and a failing accessory bearing. This table helps narrow it down.
| What you notice | Most likely cause |
|---|---|
| Squeal on start-up or in the wet, belt looks glazed or cracked | Worn belt (check tensioner too) |
| Squeal even with a new belt | Weak tensioner spring, or misalignment |
| Arm bouncing or chattering with engine running | Failed tensioner damper |
| Belt tracks off-centre or wears on one edge | Worn tensioner bushing or a misaligned pulley |
| Grinding that goes away with the belt off | A pulley or accessory bearing; spin each to find which |
| Rough or loose tensioner pulley when spun | Tensioner pulley bearing |
| Rough idler pulley when spun | Idler pulley |
| Noise stays with the belt off | Not the belt drive; look at the engine itself |
| Battery light, belt looks fine and tight | Alternator or wiring |
A useful trick: with the belt off, start the engine for a few seconds only (no longer, especially if the water pump is belt-driven, as it won't be pumping coolant). If the noise has gone, it's in the belt drive. If it's still there, it's somewhere else. Check your owner's manual first, and skip this test if you're unsure.
The Spray-Bottle Test
Mechanics often use a light mist of water on the ribbed side of a squealing belt with the engine running, keeping hands well clear. If the noise briefly gets quieter, the belt may be glazed or the tension low. If it gets louder, the cause is more likely misalignment. Treat this as a clue rather than a final answer.
Why Belt Tensioners Fail
Bad belt tensioner symptoms rarely appear out of nowhere. Tensioners work hard. They sit on the front of a hot engine, take every vibration and shock load, and never stop moving while the engine runs. Here's what wears them out:
- Heat. Engine heat slowly weakens the spring, as Underhood Service explains (Underhood Service).
- Mileage. Every turn wears the bushing, the damper and the pulley bearing.
- Contamination. Oil or coolant leaks onto the belt and tensioner speed up wear and cause slip. Fix the leak at the same time.
- Bad accessories. A seized or dragging alternator, A/C compressor or water pump shocks the belt and the tensioner.
- Wrong belt or wrong routing. A belt of the wrong length makes the arm sit outside its normal range.
How Often Should a Belt Tensioner Be Replaced?
You don't have to wait for bad belt tensioner symptoms before replacing one. There's no single interval for every engine, so follow your vehicle maker's service schedule first. As a general guide from the parts makers:
- Gates recommends inspecting the tensioner and other serpentine system components at 60,000 miles, and replacing worn components by 90,000 miles or as advised by the manufacturer (Gates).
- Dayco recommends replacing the tensioner when the belt and other front-of-engine components are changed (Dayco tech tip).
- Underhood Service notes that the tensioner is often overlooked when a belt is replaced, and should always be inspected at a belt change (Underhood Service).
Our view: if your car has done high mileage and is on its original tensioner, and you're changing the belt anyway, replacing the tensioner at the same time is sensible. The labour is almost the same, and a new belt on a tired tensioner won't last as long as it should.
Can You Drive With a Bad Belt Tensioner?
For a short time, maybe, but it's a gamble. Bad belt tensioner symptoms tend to get worse, not better. A weak or noisy tensioner can keep going for a while. The trouble is that when it finally lets go, it usually takes the belt with it, and then several systems stop at once:
- Charging stops. The battery drains until the car dies (Underhood Service).
- Cooling can stop. On engines with a belt-driven water pump, the engine starts to overheat (Underhood Service). Driving an overheating engine can cause serious damage.
- Steering can get heavy. With hydraulic power steering, the steering suddenly becomes stiff (Underhood Service).
- A/C stops blowing cold.
A seized tensioner pulley can also shred the belt, and pieces of belt can get caught in other pulleys. If the pulley is grinding, the arm is bouncing hard or the belt is fraying, don't put off the repair. If the belt has already come off, don't drive the car.
Serpentine Belt Tensioner vs Timing Belt or Chain Tensioner
People mix these up, and it matters because the jobs are completely different.
| Serpentine (drive) belt tensioner | Timing belt or chain tensioner | |
|---|---|---|
| Where | Outside the engine, on the front, easy to see | Inside the timing cover |
| What it does | Keeps the accessory belt tight | Keeps the timing belt or chain tight so the camshafts stay in time |
| Failure symptoms | Squeal, grinding, bouncing arm, slipping belt, charging or cooling problems | Rattle on cold start, timing codes, rough running; in the worst case, engine damage |
| Replacement job | Usually simple, often under an hour | Major job; timing marks must be set precisely |
This guide is about the serpentine belt tensioner. If your symptoms sound more like timing, a rattle on cold start that fades as the engine warms, for example, see the timing parts further down and get the engine checked properly.
How to Replace a Serpentine Belt Tensioner
Once you've traced bad belt tensioner symptoms to the tensioner itself, the replacement is usually simple. On many engines this is a straightforward DIY job. On some, access is tight and you'll need to remove other parts first. Always follow your vehicle's service information for bolt torques and belt routing.
- Photograph or sketch the belt routing before you start. Many cars also have a routing diagram on a label under the bonnet.
- Disconnect the battery if your service manual recommends it.
- Release the tension. Fit a breaker bar, socket or serpentine belt tool to the tensioner and rotate it to slacken the belt.
- Slip the belt off one pulley, then slowly let the tensioner back to its stop.
- Remove the belt completely and inspect it.
- Unbolt the old tensioner. Note any locating pin or dowel so the new one sits the same way.
- Clean the mounting face on the engine.
- Fit the new tensioner and torque the bolts to specification.
- Spin every other pulley while the belt is off and replace any that are rough.
- Route the new or existing belt around all pulleys except one smooth one, rotate the tensioner, slip the belt on, and release slowly.
- Check the belt sits squarely in every pulley groove and the tensioner arm is within its marks.
- Start the engine and watch the belt and arm for a minute. They should run smoothly and quietly.
Tools for the job are in our automotive tools collection.
Choosing the Right Replacement Tensioner
Tensioners are specific to the engine. Two engines in the same model can use different tensioners, and the arm angle, pulley size and mounting all need to match.
- Match the OE number. Our listings show OE and interchange numbers. Compare them with your old part or your parts catalogue.
- Check the engine. A 4-cylinder and a V6 in the same car usually have different tensioners.
- Check the pulley. Ribbed or smooth, and diameter, should match the original.
- Ask us. Send your year, model, engine and VIN through our request a part page if you're unsure.
Belt Tensioners We Stock
If you've confirmed bad belt tensioner symptoms, here's our current range. Fitment comes from the supplier listings, so check the OE numbers before ordering.
- Drive belt tensioner for the 2008–2010 Honda Accord, 2005–2010 Odyssey and 2006–2011 Pilot, OE 31170-R70-A01, with interchange numbers 89390FN, 49439 and 305390.
- Serpentine belt tensioner for the Honda Accord 2003–2007, CR-V 2002–2014 and Element 2003–2011, OE 31170RAAA01, also listed for some Acura models.
- Drive belt tensioner with pulley for the Dodge Journey, Caliber and Avenger, OE 4891595AE.
Each one is a complete assembly: arm, spring and pulley together. That's the standard repair, because the spring and bearing aren't designed to be serviced separately.
Parts the Belt Drives
Bad belt tensioner symptoms sometimes turn out to be an accessory problem, and the two are linked. A failing tensioner can take accessories down with it, and a failing accessory can kill a tensioner. If you've found damage, these are the parts to check:
Alternators
- 110A alternator for the 2013–2017 Honda Accord 2.4L
- Alternator for the 2009–2015 Toyota Camry and RAV4 2.5L
- Alternator for the Toyota Camry, Avalon, Highlander, Venza and Lexus ES350
- Alternator for the 2011–2014 Ford F-150 5.0L V8
- Alternator with decoupler pulley for the Volvo V60 and V70
Power Steering, A/C and Cooling
- Power steering pump with pulley for the 2011–2017 Honda Odyssey, 2012–2015 Pilot and 2012–2014 Ridgeline 3.5L V6
- A/C compressor with clutch for the Mitsubishi Eclipse, Galant and Endeavor
- Radiator cooling fan clutch for the 2013–2018 Ram 2500 to 5500 6.7L
Timing Parts
For timing-side jobs, we also carry a timing chain tensioner and chain kit for the Audi A3, VW Jetta and Passat 2.0T and a timing belt kit for the Ford Focus 1.5T and 1.6T.
Browse more in our engine parts, belts and hoses, alternators, cooling system and AC and HVAC collections, or shop by make: Honda, Acura, Dodge and Toyota.
When Bad Belt Tensioner Symptoms Show Up
When and how a noise appears tells you a lot. Here's what different patterns usually point to.
Only on a Cold Start
A squeal that lasts a few seconds on a cold morning and then stops often means the belt is slipping until it warms up and grips better. A slightly weak tensioner, a hardening belt or moisture on the pulleys are the usual suspects. It's an early warning worth acting on.
When the A/C Switches On
The A/C compressor adds a sudden load to the belt. If the tensioner can't hold the belt tight, it slips for a moment and squeals. Underhood Service notes that the tensioner is meant to absorb and cushion exactly this kind of shock load (Underhood Service).
When Turning the Steering at Low Speed
On cars with hydraulic power steering, turning the wheel hard at parking speed loads the pump. A short squeal at full lock points to low belt tension. Check the power steering fluid level too.
At Idle, Getting Worse Over Time
A grinding or growling noise at idle that slowly gets louder over weeks usually means a pulley bearing, either the tensioner's or another one, is wearing out.
Rattling That Comes and Goes
An intermittent rattle at idle can be a worn damper letting the arm slap against its stop. Watch the arm with the engine running to confirm.
In Wet Weather
Water on the belt reduces grip. A healthy belt drive copes; a weak tensioner or glazed belt won't. Squealing after driving through puddles or on rainy mornings is one of the most common bad belt tensioner symptoms people notice first.
Mechanical vs Hydraulic Tensioners
Most cars use a mechanical tensioner with a coil spring inside a housing. Some engines use a hydraulic tensioner, where a small hydraulic strut pushes the arm, a bit like a shock absorber. The checks are similar, with a couple of extras:
- Mechanical: check for smooth arm travel, play between the arm and body, pulley bearing condition and the wear marks.
- Hydraulic: also look for fluid leaking from the strut, and check that the strut resists movement steadily rather than collapsing or sticking.
Either way, if the tensioner fails any of these checks, replace it as a complete assembly.
What to Replace at the Same Time
When you're fixing bad belt tensioner symptoms, most of the work is getting the belt off. While it's off, it makes sense to check, and often replace, the other wear parts in the belt drive:
- The belt. If it's cracked, glazed, frayed or older than about 60,000 miles or five years, the typical service life Underhood Service gives (Underhood Service), fit a new one.
- Idler pulleys. Spin them by hand. Rough or noisy ones should go.
- Accessory bearings. Spin the alternator, power steering pump, A/C clutch and water pump pulleys. Roughness or play means that accessory needs attention.
- Leaks. Fix any oil, coolant or power steering fluid leaks onto the belt drive, or the new parts won't last.
Doing it all at once costs a little more in parts but saves taking the belt off again a few months later.
What Happens If You Ignore It
It's tempting to turn the radio up and live with a squeal. Here's how it usually goes if you do:
- The belt slips more often, especially in the wet, with the A/C on or at full steering lock.
- The slipping heats and glazes the belt. Gates notes that excessive slippage puts excessive heat into the belt and leads to premature belt failure (Gates).
- The bouncing arm hammers the accessories' bearings.
- Eventually the belt comes off or breaks, and you lose charging, cooling on many engines, and power steering.
That last step tends to happen at the worst possible moment, on a motorway or far from home. A tensioner is a small part to replace compared with an overheated engine or a tow.
Worked Examples
These are example scenarios showing how diagnosing bad belt tensioner symptoms works in practice. They're not customer stories.
The Accord That Chirps at Idle
A Honda Accord chirps at idle and squeals when the A/C comes on. The belt looks fairly new. With the engine running, the tensioner arm is bouncing noticeably. With the belt off, the arm feels notchy through its travel. That's a worn tensioner. A replacement matched to the OE number, such as the 31170RAAA01 tensioner on the models it fits, fixes the noise.
The Odyssey With Heavy Steering and a Growl
A Honda Odyssey has developed a growl from the front of the engine and the steering feels heavier at parking speeds. With the belt off, the tensioner pulley spins smoothly but the power steering pump pulley feels rough. The tensioner is fine; the pump is the problem. A replacement power steering pump on the models it fits sorts it out, and while the belt's off, the tensioner is checked and kept.
The Belt That Keeps Coming Off
A Dodge keeps throwing its belt. The belt is shredded on one edge, and the tensioner pulley sits at an angle. Classic bushing wear. The fix is a new tensioner assembly on the models it fits, plus a new belt.
The Battery Light on a Wet Morning
The battery light flickers on rainy mornings and the belt squeals. The belt is glazed and the tensioner arm is sitting at the slack end of its marks. New belt and new tensioner together, and the light stays off.
Common Mistakes
- Replacing the belt but not checking the tensioner. Underhood Service calls the tensioner often overlooked at a belt change (Underhood Service).
- Using belt dressing to stop a squeal. It hides the symptom and can make things worse.
- Not spinning the other pulleys while the belt is off. A rough idler or accessory bearing will finish off a new tensioner.
- Getting the belt routing wrong. Always photograph it first.
- Ignoring oil or coolant leaks onto the belt drive.
- Letting the tensioner snap back. The spring is strong; release it slowly.
- Ordering by model only. Match the OE number and engine.
Belt Tensioner Replacement Checklist
- Note every symptom: noise, when it happens, warning lights, steering or temperature changes.
- Watch the belt and arm running, from a safe distance.
- Check the wear indicator marks.
- Inspect the belt.
- Remove the belt, spin every pulley and move the tensioner arm through its range.
- Check for metal-to-metal contact, broken stops and leaks.
- Match the OE number and order the tensioner, plus a belt if needed.
- Photograph the belt routing, fit the new parts and check alignment.
- Run the engine and confirm the belt runs smoothly and quietly.
Frequently Asked Questions
What are the first bad belt tensioner symptoms?
Usually a squeal or chirp from the belt, or a grinding noise from the front of the engine. Gates links belt squeal to insufficient tension and treats a bouncing or chattering arm as a failed tensioner (Gates).
What does a bad belt tensioner sound like?
A squeal or chirp when the belt slips, a grinding or growling sound from a worn pulley bearing, or a rattle from the arm hitting its stop. Dayco notes that noise when turning the pulley can mean bearing failure (Dayco).
Can a bad tensioner cause the battery light to come on?
Yes. If the belt slips, the alternator doesn't charge properly, and the battery starts to run down (Underhood Service).
Can a bad belt tensioner cause overheating?
On engines where the belt drives the water pump, yes. If the belt slips or comes off, coolant stops flowing and the engine overheats (Underhood Service).
How do I test a belt tensioner?
Watch it running for bouncing or wobble, check the wear marks, then remove the belt, spin the pulley and move the arm through its range. Dayco says the arm should move smoothly from stop to stop with no play between the arm and body (Dayco).
How long does a belt tensioner last?
It varies by engine and use. Gates recommends inspecting it at 60,000 miles and replacing worn components by 90,000 miles or as the vehicle maker advises (Gates).
Should I replace the belt and tensioner together?
Often, yes. Dayco recommends replacing the tensioner when the belt and other front-of-engine components are changed (Dayco tech tip). At the very least, inspect it.
Is it safe to drive with a bad belt tensioner?
Not for long. If the belt comes off, you can lose charging, cooling and power steering at the same time. Get it fixed as soon as you can.
Is a tensioner the same as an idler pulley?
No. An idler pulley just guides the belt and has no spring. A tensioner has a spring-loaded arm that keeps the belt tight. Both have bearings that can wear.
Do you ship belt tensioners worldwide?
Yes. We ship auto parts worldwide. See our shipping page for delivery details and our order tracking page once your order is on the way.
The Bottom Line on Bad Belt Tensioner Symptoms
Bad belt tensioner symptoms are easy to spot once you know them: a squealing or chirping belt, a grinding pulley, a bouncing arm, a belt that wanders or comes off, and knock-on problems like a battery light, overheating or heavy steering. A ten-minute check, watching it run, reading the wear marks, spinning the pulley and moving the arm, will usually tell you whether the tensioner is to blame. Replace it with the belt if your car has done the miles, spin every other pulley while you're there, and the whole belt drive will run quietly again.
Ready to fix it? Browse our engine parts for belt tensioners, or check the parts your belt drives in our alternators and cooling system collections. Not sure what fits? Contact us or use our request a part page. Orders are covered by our warranty and returns policy, and our FAQ answers common questions. For related problems, read our guides to bad starter motor symptoms, bad engine mount symptoms and check engine light codes.
Sources and References
- Gates: Diagnosing tensioner failure (arm bouncing, belt squeal, bushing and damper wear, inspection and replacement mileage)
- Gates technical service bulletin on tensioners (failure signs, effect on alternator, water pump and A/C compressor)
- Dayco: What are signs the belt tensioner needs to be replaced? (noise, tracking, sticking movement, metal contact)
- Dayco tech tip: Tensioner replacement (pulley spin test, bushing wear, replacing with the belt)
- Underhood Service: Automatic belt tension, don't take it for granted (spring fatigue, wear indicators, effects on accessories, belt service life)
Written by the EasyLife Team at Easy Life Auto Parts. We sell replacement auto parts and ship them worldwide. Product details in this article come from the supplier listings on our product pages.