{"product_id":"exhaust-header-fit-for-ford-1979-1993-mustang-5-0-v8-gt-lx-svt-ban-the-sale-of-amazon","title":"Fox Body Mustang 5.0 V8 Exhaust Headers - 1982-1993 GT\/LX\/SVT","description":"\u003ch2\u003eLong-Tube Headers for the 5.0 Fox Body\u003c\/h2\u003e\n\u003cp\u003eThese are direct-fit exhaust headers built for the Fox Body Mustang's 5.0L V8, covering GT, LX and SVT Cobra models from 1982 through 1993 (1984 is excluded, since that model year used a different factory exhaust routing than the rest of the run). If your stock manifolds are cracked at the flange, rusted through after years outdoors, or just holding back a 302 that could breathe a lot easier, this header set bolts up to the factory exhaust system without any cutting or custom fabrication.\u003c\/p\u003e\n\n\u003ch2\u003eWhat These Headers Replace\u003c\/h2\u003e\n\u003cp\u003eThe cast-iron exhaust manifolds Ford put on the 5.0 Mustang are restrictive by design and prone to cracking, especially right at the flange where years of heating and cooling eventually take their toll. These headers swap that cast iron for computer mandrel-bent T-304 stainless tubing, which keeps a consistent inside diameter through every bend instead of pinching the flow path the way cheap crush-bent tubing does. The \u003ca href=\"https:\/\/en.wikipedia.org\/wiki\/Ford_Fox_platform\"\u003eFox Body platform\u003c\/a\u003e ran from 1979 to 1993 and is still one of the most widely modified Mustang generations on the road, so parts built for it, this header set included, are made for a market that knows exactly what it's bolting on and why.\u003c\/p\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eMandrel-bent T-304 stainless steel tubing for consistent, unrestricted flow\u003c\/li\u003e\n\u003cli\u003eCNC-machined flanges, TIG-welded to the primary tubes for a tight seal at the head\u003c\/li\u003e\n\u003cli\u003eResists the rust-through that eventually takes out factory cast-iron manifolds\u003c\/li\u003e\n\u003cli\u003eBolts up to the stock exhaust system on applicable years — no fabrication needed\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePrimary tube outside diameter: 1 5\/8 in.\u003c\/li\u003e\n\u003cli\u003eInlet size: 1.25 in.\u003c\/li\u003e\n\u003cli\u003eOutlet size: 2.25 in.\u003c\/li\u003e\n\u003cli\u003eMaterial: T-304 stainless steel, mandrel-bent\u003c\/li\u003e\n\u003cli\u003eFlange: CNC-machined, TIG-welded\u003c\/li\u003e\n\u003cli\u003eCondition: New\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCompatibility\u003c\/h2\u003e\n\u003cp\u003eBuilt for 1982-1993 Ford Mustang V8 models — GT, LX and SVT Cobra — fitted with the 5.0L (302) V8 only. This isn't a match for the 2.3L four-cylinder or 3.8L V6 Fox Body cars, and 1984 model-year Mustangs are excluded because that year used a different exhaust configuration than the rest of the range. If you're working from a parts-swapped or modified engine bay and aren't sure which manifold pattern you actually have, it's worth double-checking against your old manifolds before ordering, or reaching out to us first.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Owners Upgrade\u003c\/h2\u003e\n\u003cp\u003eMost people replacing these headers aren't chasing a dyno sheet — they're dealing with a manifold that's finally cracked at the collector or rusted through after fifteen-plus years of daily driving or sitting in a garage through hot summers and cold winters. A stainless header lasts long enough that this is usually a one-time job rather than something you're revisiting every few years. The flow improvement over cast iron is real too, and it's especially noticeable if the car already has a cat-back exhaust and a decent intake that could use less backpressure feeding into them from the front of the system. A lot of Fox Body owners also just like the deeper, slightly rawer exhaust note that comes with ditching the factory manifolds, even before any other exhaust work is done.\u003c\/p\u003e\n\n\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\n\u003cp\u003eHeader swaps on a Fox Body are a well-documented job in the Mustang community — expect to unbolt the old manifolds, disconnect the O2 sensor if your car has one wired into the stock manifold, and work carefully around the steering shaft and shock tower on the driver's side, which is the tightest clearance point on most 5.0 Mustangs. New gaskets and header bolts are worth having on hand, since reusing old manifold hardware under new thermal stress is a good way to end up with a stripped or snapped bolt in the head. Give the new flange bolts a re-torque after the first few heat cycles, too — it's a small step that saves a lot of chasing exhaust leaks down the road.\u003c\/p\u003e\n\n\u003ch2\u003eOrdering Information\u003c\/h2\u003e\n\u003cp\u003eThese Fox Body Mustang exhaust headers are in stock and ship ready to install. Our \u003ca href=\"\/pages\/shipping\"\u003eShipping Information\u003c\/a\u003e page covers current timelines, and our \u003ca href=\"\/pages\/warranty\"\u003eWarranty\u003c\/a\u003e and \u003ca href=\"\/pages\/returns\"\u003eReturns\u003c\/a\u003e pages explain what happens if anything isn't right on arrival. If you're not fully certain these match your specific Mustang's engine and trim, our \u003ca href=\"\/pages\/request-a-part\"\u003eRequest a Part page\u003c\/a\u003e is the fastest way to confirm fitment before you buy.\u003c\/p\u003e\n\n\u003ch2\u003eRelated Parts\u003c\/h2\u003e\n\u003cp\u003eThese headers are listed in our \u003ca href=\"\/collections\/exhaust-parts\"\u003eExhaust \u0026amp; Emissions\u003c\/a\u003e collection alongside other header and cat-back options, and in our \u003ca href=\"\/collections\/ford\"\u003eFord\u003c\/a\u003e collection with the rest of our Ford-specific inventory. Browsing either is a good way to see what else fits your Mustang, or another Ford in the family, before you check out.\u003c\/p\u003e","brand":"EasyLife Auto Parts","offers":[{"title":"Silver","offer_id":49810156945636,"sku":"CJQT243766001AZ","price":138.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/0502\/0900\/files\/00a1a785-b21d-4e5f-8ff9-cf0918143a9b.jpg?v=1788762727","url":"https:\/\/easylifeautoparts.com\/products\/exhaust-header-fit-for-ford-1979-1993-mustang-5-0-v8-gt-lx-svt-ban-the-sale-of-amazon","provider":"Easy Life Auto Parts","version":"1.0","type":"link"}