{"title":"Sensors \u0026 Electronics","description":"\u003ch2\u003eCar Sensors and Electronics That Keep the Engine Running the Way It Should\u003c\/h2\u003e\n\u003cp\u003eModern engines run on data. Dozens of \u003cstrong\u003ecar sensors\u003c\/strong\u003e feed the engine computer a constant stream of readings - oxygen levels, airflow, throttle position, temperature, crank position - and the computer uses every bit of it to decide how much fuel to add, when to fire each spark plug, and when to flag a problem. When one sensor starts sending bad data, or stops sending data at all, the engine runs badly and the check engine light comes on. We stock car sensors and related electronics for a wide range of makes and models, matched by OE and interchange number, and we ship worldwide.\u003c\/p\u003e\n\u003cp\u003eThe tricky part with sensors isn't usually finding the part - it's figuring out which one is actually at fault, since a single bad reading can throw codes that point in several directions at once. This page walks through the common sensors, what they do, and how to confirm you're replacing the right one before you spend any money.\u003c\/p\u003e\n\n\u003ch2\u003eCommon Sensors and Electronics We Carry\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOxygen (O2) sensors,\u003c\/strong\u003e which measure oxygen left in the exhaust and let the engine computer fine-tune the air-fuel mixture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMass air flow (MAF) sensors,\u003c\/strong\u003e which measure the volume and density of air entering the engine.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThrottle position sensors (TPS),\u003c\/strong\u003e which tell the computer exactly how far the throttle is open.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoolant and intake air temperature sensors,\u003c\/strong\u003e which help the computer adjust fuel delivery for a cold or hot engine.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCrankshaft and camshaft position sensors,\u003c\/strong\u003e which tell the computer exactly when each cylinder is firing and when to time the spark and injection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWheel speed (ABS) sensors,\u003c\/strong\u003e which feed the anti-lock brake and traction control systems.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIgnition coils,\u003c\/strong\u003e which aren't sensors but are closely tied to the same diagnostic codes and are often shopped for alongside them.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCommon Failure Symptoms by Sensor\u003c\/h2\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSensor\u003c\/th\u003e\n\u003cth\u003eWhat it measures\u003c\/th\u003e\n\u003cth\u003eCommon symptoms \/ codes\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eOxygen (O2) sensor\u003c\/td\u003e\n\u003ctd\u003eOxygen remaining in the exhaust\u003c\/td\u003e\n\u003ctd\u003eP0130-P0167, poor fuel economy, failed emissions test\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMass air flow (MAF)\u003c\/td\u003e\n\u003ctd\u003eAir entering the engine\u003c\/td\u003e\n\u003ctd\u003eP0100-P0104, hesitation, stalling, rough idle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eThrottle position (TPS)\u003c\/td\u003e\n\u003ctd\u003eThrottle opening angle\u003c\/td\u003e\n\u003ctd\u003eP0120-P0124, surging, erratic idle, reduced power mode\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCoolant temperature sensor\u003c\/td\u003e\n\u003ctd\u003eEngine coolant temperature\u003c\/td\u003e\n\u003ctd\u003eP0115-P0118, poor fuel economy, cooling fan running constantly\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCrank\/camshaft position sensor\u003c\/td\u003e\n\u003ctd\u003eExact engine position and timing\u003c\/td\u003e\n\u003ctd\u003eP0335-P0349, no-start, intermittent stalling\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWheel speed (ABS) sensor\u003c\/td\u003e\n\u003ctd\u003eIndividual wheel rotation speed\u003c\/td\u003e\n\u003ctd\u003eABS or traction control light, brakes pulsing unexpectedly\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIgnition coil\u003c\/td\u003e\n\u003ctd\u003eNot a sensor - fires the spark plug\u003c\/td\u003e\n\u003ctd\u003eP0300-P0308, misfires, rough running\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eIs It the Sensor, or a Wiring Problem?\u003c\/h2\u003e\n\u003cp\u003eThis is the step people skip most often, and it's the one that saves the most money. A sensor code tells you which circuit has a problem - it doesn't automatically mean the sensor itself has failed.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003ePull the exact code,\u003c\/strong\u003e not just the general description. P0101 (\"MAF range\/performance\") points differently than P0102 (\"MAF low input\").\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspect the connector and wiring\u003c\/strong\u003e at the sensor before replacing anything. Corrosion, a chewed wire, or a loose pin causes the exact same codes as a dead sensor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck for related mechanical causes.\u003c\/strong\u003e A lean fuel trim code can come from a vacuum or intake leak rather than a bad O2 or MAF sensor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClean before replacing,\u003c\/strong\u003e where it applies. A dirty MAF sensor can often be cleaned with the correct sensor-safe cleaner and will test normal afterward.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse a multimeter or scan tool's live data\u003c\/strong\u003e to check the sensor's actual output against a known-good range, rather than relying on the code alone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTest continuity on the wiring harness\u003c\/strong\u003e if the sensor tests fine electrically but the symptom persists.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eReplacing a sensor that was never the problem is one of the most common ways people end up buying the same part twice.\u003c\/p\u003e\n\n\u003ch2\u003eHow to Choose the Right Car Sensor\u003c\/h2\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eWhy it matters\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eOE \/ part number\u003c\/td\u003e\n\u003ctd\u003eThe most reliable way to match a sensor - check the connector shape too\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSensor type \/ technology\u003c\/td\u003e\n\u003ctd\u003eSome sensors (like O2 sensors) come in heated and unheated versions, or 1-wire through 4-wire designs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector shape and pin count\u003c\/td\u003e\n\u003ctd\u003eMust match exactly, even between closely related model years\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSensor location\u003c\/td\u003e\n\u003ctd\u003eUpstream vs. downstream O2 sensors, or front vs. rear, often use different part numbers\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEngine and model year\u003c\/td\u003e\n\u003ctd\u003eThe same vehicle can use different sensors across engine options\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eOEM vs. Aftermarket Sensors\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eOption\u003c\/th\u003e\n\u003cth\u003eTrade-off\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eOEM \/ OE-equivalent sensor\u003c\/td\u003e\n\u003ctd\u003eMatches original calibration closely; often the safer choice for sensitive sensors like O2 and MAF\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eQuality aftermarket sensor\u003c\/td\u003e\n\u003ctd\u003eUsually more affordable, and reliable when it's built to OE-matching specifications and tolerances\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eThe deciding factor isn't \"OEM always wins\" - it's whether the aftermarket part is actually built to match OE calibration, which varies a lot between brands. For a sensor that directly affects fuel mixture or timing, the OE part number is worth matching exactly rather than guessing with a generic listing.\u003c\/p\u003e\n\n\u003ch2\u003eReading the Codes First\u003c\/h2\u003e\n\u003cp\u003eA code names the circuit, not always the part. Pull it with a scan tool before buying anything, and cross-check it against live sensor data where your scanner supports it - that single step turns guesswork into an actual diagnosis. The \u003ca href=\"https:\/\/en.wikipedia.org\/wiki\/On-board_diagnostics\" target=\"_blank\" rel=\"noopener\"\u003eon-board diagnostics\u003c\/a\u003e article on Wikipedia explains how the OBD2 standard behind these codes actually works.\u003c\/p\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003ch3\u003eCan a bad sensor damage my engine?\u003c\/h3\u003e\n\u003cp\u003eIndirectly, yes. A bad MAF or O2 sensor can cause the engine to run too rich or too lean for an extended period, which wastes fuel and can foul spark plugs or damage the catalytic converter over time.\u003c\/p\u003e\n\u003ch3\u003eMy check engine light is on but the car drives fine. Should I worry?\u003c\/h3\u003e\n\u003cp\u003eGet the code read regardless. Some sensor faults, like a failing O2 sensor, don't affect drivability much at first but still point to a part that's wearing out and worth replacing before it fails completely.\u003c\/p\u003e\n\u003ch3\u003eCan I clear the code without fixing the sensor?\u003c\/h3\u003e\n\u003cp\u003eYou can clear it, but it will come right back once the computer detects the fault again. Clearing codes without fixing the cause just delays the diagnosis.\u003c\/p\u003e\n\u003ch3\u003eDo you ship car sensors worldwide?\u003c\/h3\u003e\n\u003cp\u003eYes. See the \u003ca href=\"\/pages\/shipping\"\u003eshipping page\u003c\/a\u003e for delivery details once your order is placed.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Buy Car Sensors From Easy Life Auto Parts\u003c\/h2\u003e\n\u003cp\u003eEvery sensor we list carries its OE or interchange reference, and our team is glad to help confirm fitment through the \u003ca href=\"\/pages\/contact\"\u003econtact page\u003c\/a\u003e before you order. We ship worldwide and back every order with a clear \u003ca href=\"\/pages\/warranty\"\u003ewarranty\u003c\/a\u003e. For the rest of your vehicle's electrical system, see \u003ca href=\"\/collections\/car-electrical-parts\"\u003ecar electrical parts\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"oxygen-sensor-234-4668-sg1857-oxygen-sensor-4pcs","title":"Oxygen Sensor 4-Pack, OE Replacement 234-4668 SG1857","description":"\u003ch2\u003eA 4-Piece Oxygen Sensor Set, OE Replacement\u003c\/h2\u003e\n\u003cp\u003eThis is a set of 4 direct-fit, threaded-in oxygen sensors, cross-referenced to part numbers 234-4668 and SG1857. If your check engine light is on with an oxygen sensor code stored, you've noticed a drop in fuel economy, or your vehicle's exhaust smells noticeably richer than usual, a worn \u003ca href=\"https:\/\/en.wikipedia.org\/wiki\/Oxygen_sensor\"\u003eoxygen sensor\u003c\/a\u003e is one of the most common and most affordable things to check first.\u003c\/p\u003e\n\u003ch2\u003eWhy Oxygen Sensors Matter So Much to How an Engine Runs\u003c\/h2\u003e\n\u003cp\u003eAn oxygen sensor measures how much unburned oxygen is left in the exhaust after combustion, and the engine computer uses that reading in real time to fine-tune how much fuel it injects on every single cycle. Because that feedback loop runs continuously while the engine is running, a sensor that's reading slowly, inaccurately, or not at all forces the computer to rely on default fuel settings that are rarely as efficient as the constantly adjusted readings a healthy sensor provides, which is why a single failing sensor can measurably affect both fuel economy and emissions.\u003c\/p\u003e\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eCross-referenced to part numbers 234-4668 and SG1857\u003c\/li\u003e\n\u003cli\u003eSet of 4 sensors for a complete replacement\u003c\/li\u003e\n\u003cli\u003e4-wire, threaded-in direct-fit design\u003c\/li\u003e\n\u003cli\u003eManufactured to OE replacement specifications\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eType: 4-wire oxygen sensor\u003c\/li\u003e\n\u003cli\u003eMounting style: Threaded-in\u003c\/li\u003e\n\u003cli\u003eQuantity: 4 sensors per set\u003c\/li\u003e\n\u003cli\u003eRecommended use: OE replacement\u003c\/li\u003e\n\u003cli\u003eCondition: New\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eCompatibility\u003c\/h2\u003e\n\u003cp\u003eThese sensors are cross-referenced to part numbers 234-4668 and SG1857. Because oxygen sensor part numbers are matched to specific engine and exhaust configurations rather than to a single universal design, it's worth confirming these numbers against your vehicle's original sensor or its OEM part number before ordering, or contacting us with your VIN if you're unsure.\u003c\/p\u003e\n\u003ch2\u003eSigns Your Oxygen Sensors Need Replacing\u003c\/h2\u003e\n\u003cp\u003eA failing oxygen sensor typically triggers a check engine light with a stored code referencing the sensor's specific location, along with symptoms like reduced fuel economy, a rough or uneven idle, a noticeable sulfur or rotten-egg smell from the exhaust, or a failed emissions test. Because most vehicles use multiple oxygen sensors positioned before and after the catalytic converter, a single sensor going bad can also cause the computer to misjudge how well the catalytic converter itself is working, sometimes triggering a second, unrelated-seeming code.\u003c\/p\u003e\n\u003ch2\u003eWhy Sensors Are Often Replaced as a Full Set\u003c\/h2\u003e\n\u003cp\u003eOxygen sensors on a given vehicle are typically installed at the same time on the assembly line and see the same heat cycling, exhaust exposure, and mileage over the life of the vehicle, which means they tend to wear out on a similar timeline even if one triggers a code before the others. Replacing all four together rather than one at a time avoids a scenario where a fresh sensor is giving the computer accurate readings while an aging one nearby has already started to drift, which can make diagnosing future issues more straightforward as well.\u003c\/p\u003e\n\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\n\u003cp\u003eReplacing these sensors means locating each sensor along the exhaust system, disconnecting its electrical connector, unscrewing it with an oxygen sensor socket or wrench, and threading in the new sensor before reconnecting the harness. Because oxygen sensor threads are sometimes coated with anti-seize compound from the factory to ease future removal, applying a small amount of anti-seize to the new sensor's threads before installation is generally recommended unless the sensor's packaging says otherwise.\u003c\/p\u003e\n\u003ch2\u003eOrdering Information\u003c\/h2\u003e\n\u003cp\u003eThis oxygen sensor set is in stock and ships ready to install. Our \u003ca href=\"\/pages\/shipping\"\u003eShipping Information\u003c\/a\u003e page covers current timelines, and our \u003ca href=\"\/pages\/warranty\"\u003eWarranty\u003c\/a\u003e and \u003ca href=\"\/pages\/returns\"\u003eReturns\u003c\/a\u003e pages explain what to do if anything isn't right on arrival. Not sure these match your specific vehicle? Our \u003ca href=\"\/pages\/request-a-part\"\u003eRequest a Part page\u003c\/a\u003e is the fastest way to confirm before you order.\u003c\/p\u003e\n\u003ch2\u003eRelated Parts\u003c\/h2\u003e\n\u003cp\u003eThis oxygen sensor set is listed in our \u003ca href=\"\/collections\/sensors-electronics\"\u003eSensors \u0026amp; Electronics\u003c\/a\u003e collection, where you'll find other engine management components for your vehicle.\u003c\/p\u003e","brand":"EasyLife Auto Parts","offers":[{"title":"4PCS","offer_id":49813858025700,"sku":"CJJT100820401AZ","price":72.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/0502\/0900\/files\/1612592965150.jpg?v=1788791004"},{"product_id":"air-flow-sensor-suitable-for-chevrolet-malibu-air-flowmeter","title":"Mass Air Flow Sensor for Chevrolet Malibu","description":"\u003ch2\u003eAn Air Flow Sensor for the Chevrolet Malibu\u003c\/h2\u003e\n\u003cp\u003eThis is a replacement \u003ca href=\"https:\/\/en.wikipedia.org\/wiki\/Mass_flow_sensor\"\u003emass air flow sensor\u003c\/a\u003e built for the Chevrolet Malibu, designed to measure the volume and density of air entering the engine so the onboard computer can calculate the correct fuel mixture. If your Malibu is running rough, hesitating on acceleration, throwing a check engine light related to the air flow or fuel trim system, or seeing a drop in fuel economy, a failing air flow sensor is a common and often overlooked cause.\u003c\/p\u003e\n\n\u003ch2\u003eWhy the Air Flow Sensor Matters So Much to Engine Performance\u003c\/h2\u003e\n\u003cp\u003eModern fuel injection depends on the engine computer knowing exactly how much air is entering the intake at any given moment, since that measurement is what determines how much fuel gets injected to keep the air-fuel ratio where it needs to be. Because this sensor sits directly in the intake air stream and reports that measurement in real time, even a partially fouled or drifting sensor can throw off fuel delivery across the entire engine, which is why a failing air flow sensor tends to affect drivability well before it triggers an outright warning light.\u003c\/p\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eDirect-fit replacement for the Chevrolet Malibu's factory air flow sensor\u003c\/li\u003e\n\u003cli\u003eRestores accurate air intake measurement for proper fuel mixture\u003c\/li\u003e\n\u003cli\u003eStraightforward plug-in electrical connection\u003c\/li\u003e\n\u003cli\u003eNew, ready-to-install condition\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eType: Mass air flow sensor\u003c\/li\u003e\n\u003cli\u003eColor: Black\u003c\/li\u003e\n\u003cli\u003eCompatible vehicle: Chevrolet Malibu\u003c\/li\u003e\n\u003cli\u003eCondition: New\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCompatibility\u003c\/h2\u003e\n\u003cp\u003eThis sensor is built for the Chevrolet Malibu. Because the Malibu has been produced across several generations and engine options over the years, and mass air flow sensor design can change between model years and engine sizes even on the same nameplate, it's essential to confirm your specific Malibu's model year and engine against your original sensor's part number before ordering.\u003c\/p\u003e\n\n\u003ch2\u003eSigns Your Air Flow Sensor Needs Replacing\u003c\/h2\u003e\n\u003cp\u003eA failing air flow sensor on the Malibu commonly shows up as a rough or unstable idle, hesitation or stumbling during acceleration, a noticeable drop in fuel economy, or a check engine light referencing mass air flow, fuel trim, or lean or rich running conditions. Because the sensor's measuring element can be affected by oil contamination from an aftermarket air filter or simple accumulated dirt over time, cleaning it is sometimes worth trying before replacement, though a sensor that's already failed internally won't be fixed by cleaning alone.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Getting the Right Sensor Matters\u003c\/h2\u003e\n\u003cp\u003eAn air flow sensor that doesn't match your Malibu's exact engine and intake design can report inaccurate readings even when it's technically installed correctly, which defeats the purpose of the replacement in the first place. Confirming your original sensor's part number and your vehicle's exact model year and engine before ordering is the most reliable way to make sure the replacement measures airflow the way your engine's computer expects.\u003c\/p\u003e\n\n\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\n\u003cp\u003eReplacing this sensor typically means locating it in the intake tract between the air filter housing and the throttle body, disconnecting the electrical connector, removing the mounting screws or clips holding it in place, and installing the new sensor in reverse order. Because the sensor's measuring element is delicate, handling it carefully during installation and avoiding touching the sensing wire or element directly will help it perform the way it's designed to.\u003c\/p\u003e\n\n\u003ch2\u003eOrdering Information\u003c\/h2\u003e\n\u003cp\u003eThis air flow sensor is in stock and ships ready to install. Our \u003ca href=\"\/pages\/shipping\"\u003eShipping Information\u003c\/a\u003e page covers current timelines, and our \u003ca href=\"\/pages\/warranty\"\u003eWarranty\u003c\/a\u003e and \u003ca href=\"\/pages\/returns\"\u003eReturns\u003c\/a\u003e pages explain what to do if anything isn't right on arrival. Not sure this matches your specific Malibu's model year and engine? Our \u003ca href=\"\/pages\/request-a-part\"\u003eRequest a Part page\u003c\/a\u003e is the fastest way to confirm before you order.\u003c\/p\u003e\n\n\u003ch2\u003eRelated Parts\u003c\/h2\u003e\n\u003cp\u003eThis air flow sensor is listed in our \u003ca href=\"\/collections\/chevrolet\"\u003eChevrolet\u003c\/a\u003e collection, along with our \u003ca href=\"\/collections\/sensors-electronics\"\u003eSensors \u0026amp; Electronics\u003c\/a\u003e collection, where you'll find other engine management components for the Malibu.\u003c\/p\u003e\n","brand":"EasyLife Auto Parts","offers":[{"title":"Black","offer_id":49813873721572,"sku":"CJJT170523701AZ","price":45.41,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/0502\/0900\/files\/8d01ef59-70ba-4895-84c3-0b0883c3ac1a.jpg?v=1788791206"},{"product_id":"automotive-throttle-position-sensor-automotive-parts","title":"Throttle Position Sensor - OEM 3140173 (22mm) \/ 3131705 (26mm)","description":"\u003ch2\u003eA Throttle Position Sensor, Available in Two Sizes\u003c\/h2\u003e\n\u003cp\u003eThis is a replacement throttle position sensor, available in two OEM specifications — part number 3140173 in a 22mm size and part number 3131705 in a 26mm size. If your engine has developed a rough idle, hesitation on acceleration, or an intermittent check engine light related to throttle input, a worn or drifting throttle position sensor is a common and relatively inexpensive cause worth ruling out.\u003c\/p\u003e\n\u003ch2\u003eWhat a Throttle Position Sensor Does\u003c\/h2\u003e\n\u003cp\u003eThe throttle position sensor tells your engine's computer exactly how far the throttle plate is open at any given moment, which the computer uses alongside other sensor data to calculate how much fuel to inject and how to time ignition. It's a small potentiometer or hall-effect sensor mounted on the throttle body, and it needs to report a smooth, accurate voltage across the full range of throttle movement for the engine to run correctly. When the sensor wears internally or the signal starts to drift, the computer gets bad information and compensates poorly, which is where the symptoms below come from.\u003c\/p\u003e\n\u003ch2\u003eSigns Yours Might Be Failing\u003c\/h2\u003e\n\u003cp\u003eA failing throttle position sensor often shows up as a rough or fluctuating idle, hesitation or a flat spot when you press the accelerator, unexpected surges in RPM without any change in pedal input, or a check engine light referencing throttle position or a related fault code. Some vehicles will also enter a reduced-power \"limp\" mode if the computer decides the sensor data is unreliable enough to be unsafe to use normally. None of these symptoms are exclusive to a bad TPS — a dirty throttle body or a vacuum leak can cause similar issues — so it's worth confirming with a code reader or a multimeter check on the sensor's voltage output before assuming this is the fix you need.\u003c\/p\u003e\n\u003ch2\u003eTwo Sizes, Two Part Numbers\u003c\/h2\u003e\n\u003cp\u003eThis listing covers two OEM specifications: part number 3140173, sized at 22mm, and part number 3131705, sized at 26mm. These aren't interchangeable with each other — the sensor has to physically match your throttle body's mounting bore, so check which size and part number matches your vehicle's original sensor before ordering rather than guessing based on engine size or make alone.\u003c\/p\u003e\n\u003ch2\u003eA Note on Compatibility\u003c\/h2\u003e\n\u003cp\u003eWe don't have a specific vehicle application list on file for either size beyond the OEM part numbers themselves, so we're not going to claim broad compatibility we can't confirm. The safest way to order the correct one is to match either 3140173 or 3131705 directly against the number stamped on your current sensor, or against your vehicle's parts catalog. If you're not sure which one you need, reach out through our \u003ca href=\"\/pages\/request-a-part\"\u003eRequest a Part page\u003c\/a\u003e with your vehicle details and we'll help you confirm.\u003c\/p\u003e\n\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\n\u003cp\u003eReplacing a throttle position sensor is typically a straightforward job — it's usually held on with two small screws on the throttle body and connects through a simple electrical plug. Once replaced, some vehicles require the engine computer to relearn the throttle's idle position, which can happen automatically after a short drive cycle or may need a manual reset procedure depending on your specific make and model — it's worth checking your vehicle's service information for that detail before assuming the job is finished at the last bolt.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eType: Throttle position sensor\u003c\/li\u003e\n\u003cli\u003eOEM part number: 3140173 (22mm)\u003c\/li\u003e\n\u003cli\u003eOEM part number: 3131705 (26mm)\u003c\/li\u003e\n\u003cli\u003eMeasurement range: Standard\u003c\/li\u003e\n\u003cli\u003eCondition: New\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFor more on how these sensors work alongside the rest of the engine management system, Wikipedia's \u003ca href=\"https:\/\/en.wikipedia.org\/wiki\/Throttle_position_sensor\"\u003ethrottle position sensor article\u003c\/a\u003e covers the sensor technology and signal types in more technical depth.\u003c\/p\u003e\n\u003ch2\u003eOrdering Information\u003c\/h2\u003e\n\u003cp\u003eThis throttle position sensor is in stock in both sizes and ships ready to install. Our \u003ca href=\"\/pages\/shipping\"\u003eShipping Information\u003c\/a\u003e page covers current timelines, and our \u003ca href=\"\/pages\/warranty\"\u003eWarranty\u003c\/a\u003e and \u003ca href=\"\/pages\/returns\"\u003eReturns\u003c\/a\u003e pages explain what to do if the size you ordered turns out to be wrong.\u003c\/p\u003e\n\u003ch2\u003eRelated Parts\u003c\/h2\u003e\n\u003cp\u003eThis sensor sits in our \u003ca href=\"\/collections\/sensors-electronics\"\u003esensors and electronics\u003c\/a\u003e collection and our \u003ca href=\"\/collections\/electrical-parts\"\u003eelectrical parts\u003c\/a\u003e collection. If you're diagnosing a throttle or idle issue and aren't yet certain the TPS is the cause, it's worth browsing those collections for other related sensors.\u003c\/p\u003e","brand":"EasyLife Auto Parts","offers":[{"title":"22mm \/ Black","offer_id":49813912158436,"sku":"CJYD277834701AZ","price":29.94,"currency_code":"USD","in_stock":true},{"title":"26mm \/ Black","offer_id":49813912191204,"sku":"CJYD277834702BY","price":29.94,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/0502\/0900\/files\/67a2c5c6-40aa-4098-a46f-f640ad8a28ee.jpg?v=1788791493"},{"product_id":"automotive-ignition-coil-high-voltage-package","title":"High Voltage Ignition Coil - Model BK-6160 Replacement","description":"\u003ch2\u003eA High Voltage Ignition Coil, Model BK-6160\u003c\/h2\u003e\n\u003cp\u003eThis is a replacement ignition coil, model BK-6160, built to deliver the high-voltage spark that fires your engine's spark plugs. If your car has started misfiring, hesitating, or throwing a rough idle, a weak or failing ignition coil is one of the more common culprits, and replacing it is usually a straightforward fix once you've confirmed that's actually the problem.\u003c\/p\u003e\n\u003ch2\u003eWhat an Ignition Coil Does\u003c\/h2\u003e\n\u003cp\u003eYour car's battery only puts out 12 volts, which isn't nearly enough to jump the gap on a spark plug and ignite the air-fuel mixture in the cylinder. The ignition coil's job is to take that low voltage and step it up dramatically — often into the tens of thousands of volts — timed precisely with each cylinder's firing order. When a coil starts to weaken, the spark it produces gets thinner and less consistent, which shows up as a misfire, a check engine light, reduced fuel economy, or a noticeable loss of power under acceleration. If you want the more technical explanation of the step-up transformer principle behind this, Wikipedia's \u003ca href=\"https:\/\/en.wikipedia.org\/wiki\/Ignition_coil\"\u003eignition coil article\u003c\/a\u003e covers the electromagnetic side of it in more depth than we will here.\u003c\/p\u003e\n\u003ch2\u003eWhat You're Getting\u003c\/h2\u003e\n\u003cp\u003eThis listing is for one high voltage ignition coil, model BK-6160, classified as a general automotive spare part. It's built to replace a coil that's failed or is showing signs of weakening, restoring proper spark delivery to the cylinder it serves. As with most ignition coils, this is sold as an individual unit rather than a full engine set, so check whether your vehicle needs one coil replaced or several before ordering quantity.\u003c\/p\u003e\n\u003ch2\u003eA Note on Compatibility\u003c\/h2\u003e\n\u003cp\u003eWe don't have a specific vehicle application list attached to this coil beyond the BK-6160 model designation, so we're not going to claim it fits a particular make or model without that confirmation. Ignition coils are one of those parts where the physical connector, mounting style, and electrical specifications have to match your engine exactly — a coil that looks similar but isn't the correct fit either won't seat properly or won't deliver the voltage your engine needs. If you're not already working from a confirmed cross-reference against your vehicle's OEM coil number, the safest approach is to compare this BK-6160 designation against your existing coil or your vehicle's parts catalog before ordering, or reach out through our \u003ca href=\"\/pages\/request-a-part\"\u003eRequest a Part page\u003c\/a\u003e and we'll help you confirm fitment.\u003c\/p\u003e\n\u003ch2\u003eSigns You Might Need One\u003c\/h2\u003e\n\u003cp\u003eA failing ignition coil often shows up first as a rough idle or a slight hesitation when you accelerate, especially noticeable at low RPM. As it gets worse, you may notice an intermittent misfire that feels like the engine briefly stumbles, sometimes accompanied by a flashing check engine light, which usually indicates the engine control computer has detected a misfire on a specific cylinder. Some drivers also notice reduced fuel economy, since an engine running on a weak spark doesn't burn fuel as efficiently as it should. None of these symptoms are exclusive to a bad coil — spark plugs, fuel injectors, and wiring issues can cause similar problems — so it's worth ruling out the simpler and cheaper possibilities first if you're not sure.\u003c\/p\u003e\n\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\n\u003cp\u003eReplacing an ignition coil is one of the more approachable jobs in home auto maintenance on most vehicles, particularly on engines with coil-on-plug designs where the coil sits directly above each spark plug. Typically it involves disconnecting the electrical connector, removing a single retaining bolt, and pulling the old coil straight up and off the spark plug before reversing the process with the new one. It's worth inspecting the spark plug underneath while you're in there, since a worn plug can shorten the life of a brand new coil if it's not replaced at the same time.\u003c\/p\u003e\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eType: High voltage ignition coil\u003c\/li\u003e\n\u003cli\u003eModel: BK-6160\u003c\/li\u003e\n\u003cli\u003eClassification: Automotive spare part\u003c\/li\u003e\n\u003cli\u003eCondition: New\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhy This Is Worth Getting Right\u003c\/h2\u003e\n\u003cp\u003eDriving on a failing ignition coil for an extended period can do more damage than the coil itself would cost to replace — unburned fuel from a misfiring cylinder can wash oil off the cylinder walls and, in some cases, damage the catalytic converter if raw fuel keeps making it into the exhaust system. Catching a weak coil early and swapping it out is a lot cheaper than dealing with a fouled catalytic converter down the line.\u003c\/p\u003e\n\u003ch2\u003eOrdering Information\u003c\/h2\u003e\n\u003cp\u003eThis ignition coil is in stock and ships as a single unit, ready to install once you've confirmed it's the right match for your vehicle. Our \u003ca href=\"\/pages\/shipping\"\u003eShipping Information\u003c\/a\u003e page covers current timelines, and our \u003ca href=\"\/pages\/warranty\"\u003eWarranty\u003c\/a\u003e and \u003ca href=\"\/pages\/returns\"\u003eReturns\u003c\/a\u003e pages explain the process if anything needs to go back.\u003c\/p\u003e\n\u003ch2\u003eRelated Parts\u003c\/h2\u003e\n\u003cp\u003eThis coil sits in our \u003ca href=\"\/collections\/electrical-parts\"\u003eelectrical parts\u003c\/a\u003e collection and our \u003ca href=\"\/collections\/sensors-electronics\"\u003esensors and electronics\u003c\/a\u003e collection alongside our other ignition and electrical components. If you're diagnosing a misfire and aren't yet certain the coil is the cause, it's worth browsing those collections for related sensors and electrical parts that can cause similar symptoms.\u003c\/p\u003e","brand":"EasyLife Auto Parts","offers":[{"title":"Black","offer_id":49813915730148,"sku":"CJQCQCQT00105-Black","price":44.52,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/0502\/0900\/files\/1258034827932.jpg?v=1788791674"},{"product_id":"auto-parts-ignition-coil","title":"Single-Cylinder Ignition Coil for Chery Fengyun, Pika \u0026 Huapu","description":"\u003ch2\u003eSingle-Cylinder Ignition Coil for Chery Fengyun, Pika \u0026amp; Huapu\u003c\/h2\u003e\n\u003cp\u003eThis is a single-cylinder \u003ca href=\"https:\/\/en.wikipedia.org\/wiki\/Ignition_coil\"\u003eignition coil\u003c\/a\u003e cross-referenced to item numbers 0221503004 and 0221503465, built for the Chery Fengyun, Pika, and Huapu. If your engine has developed a rough idle, an intermittent misfire, or has become harder to start than it used to be, a tired ignition coil is one of the most common and most overlooked causes on small-displacement single-cylinder engines like these.\u003c\/p\u003e\n\n\u003ch2\u003eWhy the Ignition Coil Matters on a Single-Cylinder Engine\u003c\/h2\u003e\n\u003cp\u003eOn a single-cylinder engine, there's no second or third coil to pick up the slack if one starts to fail, so the entire engine's running quality depends on that one coil delivering a strong, consistent spark every cycle. A coil that's beginning to break down internally, whether from age, heat cycling, or a cracked winding, tends to show up as a gradual loss of power and smoothness rather than a sudden failure, which is why many owners live with a slowly worsening problem for a while before tracking it back to the coil.\u003c\/p\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eCross-referenced to item numbers 0221503004 and 0221503465\u003c\/li\u003e\n\u003cli\u003eBuilt specifically for single-cylinder applications on the Chery Fengyun, Pika, and Huapu\u003c\/li\u003e\n\u003cli\u003eDirect-fit replacement designed to restore factory ignition performance\u003c\/li\u003e\n\u003cli\u003eStraightforward one-coil design for a simple, uncomplicated installation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eType: Automobile ignition coil\u003c\/li\u003e\n\u003cli\u003eApplicable engine cylinder quantity: Single cylinder\u003c\/li\u003e\n\u003cli\u003eItem numbers: 0221503004, 0221503465\u003c\/li\u003e\n\u003cli\u003eQuantity: 1 coil\u003c\/li\u003e\n\u003cli\u003eCondition: New\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCompatibility\u003c\/h2\u003e\n\u003cp\u003eBuilt for the Chery Fengyun, Pika, and Huapu single-cylinder applications. Because ignition coil fitment can vary between production years and engine variants even within the same model line, it's worth confirming the item numbers above against your original coil or your vehicle's documentation before ordering, or reaching out with your vehicle's details for help confirming fitment.\u003c\/p\u003e\n\n\u003ch2\u003eSigns You Need a New Ignition Coil\u003c\/h2\u003e\n\u003cp\u003eA rough or uneven idle, a noticeable loss of power under load, an engine that's become harder to start, especially in cold or damp conditions, or an intermittent misfire that comes and goes are all common signs of a failing ignition coil. On a single-cylinder engine, these symptoms tend to be more pronounced than on a multi-cylinder engine, since there's no other cylinder firing normally to mask the problem.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Replacing a Failing Coil Promptly Matters\u003c\/h2\u003e\n\u003cp\u003eContinuing to run an engine on a weak or failing ignition coil can lead to unburned fuel passing through the combustion chamber, which wastes fuel and can foul spark plugs faster than normal. Over time, this also puts extra strain on the starter and battery, since a poor spark makes the engine harder to start and keep running. Replacing the coil before it fails completely helps avoid getting stranded with an engine that won't start at all.\u003c\/p\u003e\n\n\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\n\u003cp\u003eInstalling this coil means disconnecting the negative battery terminal first, removing the electrical connector and mounting hardware from the old coil, and securing the new coil in its place before reconnecting the wiring. Because a loose or improperly seated connector can cause the same misfire symptoms as a failing coil, double-checking that the connection is fully seated after installation is worth the extra minute it takes. It's also a good idea to inspect the spark plug itself while the coil is off, since a worn or fouled plug paired with a new coil can still leave you with the same rough-running symptoms you started with.\u003c\/p\u003e\n\n\u003ch2\u003eOrdering Information\u003c\/h2\u003e\n\u003cp\u003eThis ignition coil is in stock and ships ready to install. Our \u003ca href=\"\/pages\/shipping\"\u003eShipping Information\u003c\/a\u003e page covers current timelines, and our \u003ca href=\"\/pages\/warranty\"\u003eWarranty\u003c\/a\u003e and \u003ca href=\"\/pages\/returns\"\u003eReturns\u003c\/a\u003e pages explain what to do if anything isn't right on arrival. Not sure this matches your specific vehicle and engine variant? Our \u003ca href=\"\/pages\/request-a-part\"\u003eRequest a Part page\u003c\/a\u003e is the fastest way to confirm before you order.\u003c\/p\u003e\n\n\u003ch2\u003eRelated Parts\u003c\/h2\u003e\n\u003cp\u003eThis ignition coil is listed in our \u003ca href=\"\/collections\/engine-parts\"\u003eEngine Parts\u003c\/a\u003e collection, along with our \u003ca href=\"\/collections\/electrical-parts\"\u003eElectrical Parts\u003c\/a\u003e collection, where you'll find other ignition and electrical components.\u003c\/p\u003e\n","brand":"EasyLife Auto Parts","offers":[{"title":"Black","offer_id":49813935718628,"sku":"CJYD246256601AZ","price":42.55,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/0502\/0900\/files\/9bda92d9-15e1-48ea-95ba-2124ccba8b86.jpg?v=1788791953"},{"product_id":"automotive-obd2-scanner-obd-code-reader-car-check-engine-fault-diagnostic-tool","title":"Automotive OBD2 Scanner, OBD Code Reader \u0026 Check Engine Fault Diagnostic Tool","description":"\u003ch2\u003eAutomotive OBD2 Scanner, OBD Code Reader \u0026amp; Check Engine Fault Diagnostic Tool\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eImportant Notice: this is a clearance item and does not include after-sales support, including for lost packages or quality issues. Please review the details below carefully before ordering.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThis is a V320 \u003ca href=\"https:\/\/en.wikipedia.org\/wiki\/On-board_diagnostics\"\u003eOBD2\u003c\/a\u003e code reader and diagnostic scanner supporting all nine standard OBD II\/EOBD communication protocols, built to read and clear check engine fault codes, display live data streams, and test battery voltage across virtually any vehicle built on the OBD2 standard. If your check engine light has come on and you want to know what triggered it before heading to a shop, this scanner gives you that information directly from your own driveway.\u003c\/p\u003e\n\n\u003ch2\u003eWhy an OBD2 Scanner Is Worth Having\u003c\/h2\u003e\n\u003cp\u003eA check engine light on its own tells you almost nothing beyond \"something needs attention,\" and a shop visit just to read a code can cost more than a scanner of your own. Having a dedicated OBD2 reader on hand means you can pull the exact fault code yourself, look up what it means, and decide whether it's something you can address yourself or something that needs a professional, before you spend a dime on diagnosis.\u003c\/p\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eSupports all nine standard OBD II\/EOBD protocols for broad vehicle compatibility\u003c\/li\u003e\n\u003cli\u003eReads and clears check engine fault codes, with detailed code lookup information\u003c\/li\u003e\n\u003cli\u003eLive data stream display for engine speed, temperature, fuel consumption, and more\u003c\/li\u003e\n\u003cli\u003eBattery voltage testing, freeze frame data, MIL status check, and I\/M readiness status\u003c\/li\u003e\n\u003cli\u003eMulti-language support across eight languages, including English, Spanish, French, and German\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eType: OBD2\/EOBD diagnostic scanner (model V320)\u003c\/li\u003e\n\u003cli\u003eSupported protocols: SAE J1850 PWM, SAE J1850 VPW, ISO9141-2, ISO14230-4 KWP (standard and fast init), ISO15765-4 CAN (11-bit and 29-bit ID, 500 and 250 Kbaud)\u003c\/li\u003e\n\u003cli\u003eMaterial: ABS housing\u003c\/li\u003e\n\u003cli\u003eColor: Black\u003c\/li\u003e\n\u003cli\u003eDimensions: Approximately 195 x 100 x 30mm\u003c\/li\u003e\n\u003cli\u003eSupported languages: English, German, French, Spanish, Italian, Russian, Dutch, Chinese\u003c\/li\u003e\n\u003cli\u003eWhat's included: Scanner unit, OBD connection cable, English manual\u003c\/li\u003e\n\u003cli\u003eCondition: New (clearance item, no after-sales support)\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCompatibility\u003c\/h2\u003e\n\u003cp\u003eThis scanner supports any vehicle built to the OBD II\/EOBD standard, which covers virtually all gasoline vehicles sold in the United States since 1996 and most since the early 2000s in other markets. Per the manufacturer's own notes, it is not compatible with new energy vehicles, hybrid vehicles, or any model that does not conform to the OBD2 protocol, so it's worth confirming your vehicle uses a standard OBD2 port before relying on this tool.\u003c\/p\u003e\n\n\u003ch2\u003eWhat You Can Check With This Scanner\u003c\/h2\u003e\n\u003cp\u003eBeyond basic fault code reading and clearing, this scanner can run acceleration and braking performance tests, read live engine data such as RPM and coolant temperature, check oxygen sensor status, test the fuel evaporation system, and pull basic vehicle information like the VIN. A green status light confirms the vehicle supports diagnostics, a yellow light flags a detected fault, and a red light confirms the device itself is powered and connected correctly.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Reading Your Own Codes Matters\u003c\/h2\u003e\n\u003cp\u003eKnowing the specific fault code behind a check engine light turns a vague warning into an actionable diagnosis, whether that means checking a loose gas cap, planning a specific repair, or simply confirming a light will clear on its own after a minor issue is resolved. For anyone who does their own basic maintenance, this scanner turns troubleshooting from guesswork into a straightforward, code-driven process.\u003c\/p\u003e\n\n\u003ch2\u003eSetup Notes\u003c\/h2\u003e\n\u003cp\u003eUsing this scanner means locating your vehicle's OBD port, typically found under the dash near the steering column, connecting the scanner with the included cable, and starting the vehicle so the systems can communicate. From the main menu, selecting the OBD\/EOBD option opens the test functions, where you can choose fault code reading, live data streams, performance tests, or voltage detection. Because this is a clearance item without after-sales support, testing the connection and a basic code read as soon as it arrives is worth doing so you know it's working for your vehicle.\u003c\/p\u003e\n\n\u003ch2\u003eOrdering Information\u003c\/h2\u003e\n\u003cp\u003eThis scanner is in stock and ships ready to use. As noted above, this is a clearance item sold without after-sales support, including for lost packages or quality issues, so please review the specifications carefully before ordering. Our \u003ca href=\"\/pages\/shipping\"\u003eShipping Information\u003c\/a\u003e page covers current timelines, and our \u003ca href=\"\/pages\/warranty\"\u003eWarranty\u003c\/a\u003e and \u003ca href=\"\/pages\/returns\"\u003eReturns\u003c\/a\u003e pages explain our general policies. Have a question before you buy? Our \u003ca href=\"\/pages\/request-a-part\"\u003eRequest a Part page\u003c\/a\u003e is the fastest way to reach us.\u003c\/p\u003e\n\n\u003ch2\u003eRelated Parts\u003c\/h2\u003e\n\u003cp\u003eThis scanner is listed in our \u003ca href=\"\/collections\/tools-garage-equipment\"\u003eTools \u0026amp; Garage Equipment\u003c\/a\u003e collection, along with our \u003ca href=\"\/collections\/sensors-electronics\"\u003eSensors \u0026amp; Electronics\u003c\/a\u003e collection, where you'll find other diagnostic and testing tools.\u003c\/p\u003e\n","brand":"EasyLife Auto Parts","offers":[{"title":"Black","offer_id":49816318017764,"sku":"CJZD231909601AZ","price":64.8,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/0502\/0900\/files\/d113365f-d226-40e2-9266-14196ef8b76a.jpg?v=1788808402"},{"product_id":"1pc-front-right-passenger-power-window-regulator-w-motor-fit-for-titan-04-15","title":"1pc Front Right Passenger Power Window Regulator W Motor Fit For Titan 04-15","description":"\u003cp\u003e\n \u003cstrong\u003e【Application】\u003c\/strong\u003e\n \u003cbr\u003e\n fit for Nissan Armada 2005-2015 \n \u003cbr\u003e\n fit for Nissan Pathfinder Armada 2004 \n \u003cbr\u003e\n fit for Nissan Titan 2004-2015 \n \u003cbr\u003e\n fit for Infiniti QX56 2004-2010 \n\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\n \u003cstrong\u003e【Reference OE\/ OEM Number】\u003c\/strong\u003e\n \u003cbr\u003e\n 748525, 748-525, 388613, 660537, 80720ZT00A\n \u003cbr\u003e\n 80720-ZT00A, 807309FJ0A, 80730-9FJ0A, 807207S000\n \u003cbr\u003e\n 80720-7S000, 80730ZE00A, 80730-ZE\n\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\n \u003cstrong\u003e【Specification】\u003c\/strong\u003e\n \u003cbr\u003e\n Type: Window Regulator\n \u003cbr\u003e\n Material: Metal; Plastic\n \u003cbr\u003e\n Condition: 100% Brand New\n \u003cbr\u003e\n Manufacture Warranty: 2 Years\n \u003cbr\u003e\n Placement on Vehicle: Front Right (Passenger Side)\n \u003cbr\u003e\n Lifting Mechanism Type: Cable Type\n \u003cbr\u003e\n Terminal Quantity: 6-Pin\n \u003cbr\u003e\n Motor Included: Yes\n\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\n \u003cstrong\u003e【Package Includes】\u003c\/strong\u003e\n \u003cbr\u003e\n 1x Window Regulator w\/ Motor\n\u003c\/p\u003e\n\u003cp\u003e\n \u003cbr\u003e\n \u003cstrong\u003e【Features】\u003c\/strong\u003e\n \u003cbr\u003e\n -Superior Longevity\n \u003cbr\u003e\n Premium-Grade Materials And Reinforced Components Guarantee Adaptive Durability.\n\u003c\/p\u003e\n\u003cp\u003e\n -Direct Bolt-On Installation\n \u003cbr\u003e\n Factory-calibrated Precision fit for Direct-fit Installation.\n\u003c\/p\u003e\n\u003cp\u003e\n -High-Torque Quiet Drive\n \u003cbr\u003e\n Offering Formidable Lifting Capacity fit for Intensive Workloads With Remarkably Quiet Operation.\n\u003c\/p\u003e\n\u003cp\u003e\n \u003cbr\u003e\n  \n\u003c\/p\u003e\n\u003cp\u003e\n \u003cbr\u003e\n \u003cstrong\u003e\n  a. Notice\n  \u003cbr\u003e\n  1. California Prop 65 Warning\n  \u003cbr\u003e\n  2. Authority ID：MXR02FXSY（Very important, please do not delete）\n \u003c\/strong\u003e\n\u003c\/p\u003e\n\u003cp\u003e\n \u003cimg src=\"https:\/\/cf.cjdropshipping.com\/776d6421-1f58-4820-8ab4-77b78ae0dd9f.jpg\" style=\"max-width:100%;\" contenteditable=\"false\"\u003e\n \u003cimg src=\"https:\/\/cf.cjdropshipping.com\/b23d18ff-9cab-4bf9-be17-9092820a7767.jpg\" style=\"max-width:100%;\" contenteditable=\"false\"\u003e\n \u003cimg src=\"https:\/\/cf.cjdropshipping.com\/288ca102-480d-4436-94a3-52e9186a1bce.jpg\" style=\"max-width:100%;\" contenteditable=\"false\"\u003e\n \u003cimg src=\"https:\/\/cf.cjdropshipping.com\/be6448cf-43f5-4c89-af72-d35e20084a0c.jpg\" style=\"max-width:100%;\" contenteditable=\"false\"\u003e\n \u003cimg src=\"https:\/\/cf.cjdropshipping.com\/e57951eb-1df0-4b4e-894a-fd333d76353c.jpg\" style=\"max-width:100%;\" contenteditable=\"false\"\u003e\n \u003cimg src=\"https:\/\/cf.cjdropshipping.com\/c9139e34-006d-4557-b3f4-c2be7d28f2f0.jpg\" style=\"max-width:100%;\" contenteditable=\"false\"\u003e\n\u003c\/p\u003e","brand":"EasyLife Auto Parts","offers":[{"title":"98566353","offer_id":49912315347172,"sku":"CJQT315314401AZ","price":100.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/0502\/0900\/files\/1c619164-c5d6-4d65-a072-09c040374763.jpg?v=1789827232"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0740\/0502\/0900\/collections\/1612592965150.jpg?v=1791873432","url":"https:\/\/easylifeautoparts.com\/collections\/car-sensors.oembed","provider":"Easy Life Auto Parts","version":"1.0","type":"link"}